gauge

Selling used gauge OEM in good condition, lcd screen might need to be replaced, panel is also for sale

Hello, I am a new owner of a 2010 Sundeck 260 and have an issue where the fuel gauge isn't properly reading the level of fuel. I've done some research and digging and see that I can try to test the sending unit and the fuel gauge, but this isn't as simple as I thought for two reasons: 1. The...

Hopefully not jinxing this but I will be buying a used 2016 270 Sundeck next week. It has the standard four analogue gauge cluster but I’m hoping to swap that out for the digital dash /chartplotter that was an upgrade option when sold new... As a newbie to Sea Ray boats I was wondering if anyone...

Hello everybody I’m from France :) I have a Sea ray 290 Bow Rider from 2001. My boat is being restored and I’m looking for change the bezels of all my gauges. All the bezel are « broken » and very old. Impossible to find on internet compatible bezel for this gauges. i fount this but I think...

I own a 2017 SeaRay 260 and having an battery or electrical issue. It started out as a possible bad battery after winter storage. When Battery Control Knob were set to #1 position, and key turned half-way (engine start not attempted), the console gauges were not working. I thought - ok...

Any thoughts or advice? When I fill it--it reads full. After a half day of boating it drops to 1/2 a tank. If I go to fill it up--it only takes 5 gallons. I have a 22 gallon tank according to my owner's manual. After a full day of boating (or two half days), it reads empty. If I go fill it...

Hello, all, any advice is very appreciated. In short, when I turn the key, nothing happens now. No response on the gauges and meters on the dash board, no cranking at all. But water blowers, gas blower, boat light are OK. And I can move up and down the motor with the button on gas lever. Due to...

I'm having a nagging problem with my fuel gauge, both analog and SmartCraft (they have always matched, so I know it's not the gauge itself). I have a 2007 240SD with 350 Mag. Last year, both indicators went dead. However the GPH and gallons used still worked, so I finished the summer always...

looking for 01-02 searay 300 gauges 4 in 1 gauge with oil pressure top left,water temp top right,trim on bottom right and battery voltage on bottom left. please send pics if any available. if not gauge anyone no where someone might get this repaired

I have owned this new to us Sea Ray for a little over a month now. To date, new cockpit carpets ordered plus a new port side sun pad to go with the centreline one and other custom starboard cushion. We've spent a whack of time cleaning, getting ready for the weather to break here in the...

I replaced the trim/limit senders on both of my drives recently. they work great! the limit switches are now adjusted correctly, and so are the trim senders. Here is my issue; my gauges are foggy, so I bought some new ones. they are the old teleflex style with the chrome ring, and it is...

I have a 2000 270DA with the twins. Last year, I replaced all trim senders and limit switches, and everything was working great. I just splashed this year, and neither of my trim gauges will do anything. I double cheched the senders, and they look great. I then replaced the gauges because it...

I have a 2001 280 DA w/ twin 4.3 Alpha Drives the starboard engine is running hot. When I took it in the service dept. said the engine was fine but the gauge is bad. The temp gauge is heating up faster than port but when running it will go to 0 and then back to 170 degrees+. The overheat...

I recently purchased a 2002 320 Sundancer. A few weeks ago i noticed condensation in a few of my gauges. It has since dried but left a residue on the inside of the glass. My question is can the glass be removed from the gauge? If so how? Thank You

Hi! Changed the trim sender kit last year. After this the trim meter on the dash board moves just a tiny bit until it swings full up. the trim limit is working fine , and so is the trailer switch part as well. From what i found the resistance in the sender is 0-240 ohms. but running the meter...