Can someone point me towards a probable cause for the touch pad on the console od my 240da not working. Its been setting a while and the last time i used it everything worked fine, but now none of the buttons function.
Is the a master fuse somewhere that could have blown. Any insight would be...
The tempurature according to weather bug right now is 30 in Tampa. I had to take the boat off the lift and put it in the water so I could run the heater. I got the lights on and the heat set to 68 in hopes of keeping this hard freeze from cracking the block or any of the water lines in the boat...
So I had a wonderfull day on the water last Saturday. then I washup the boat and flush it just to notice that my smartcraft water flow is showing 0.0 flow to 0.1 :smt013. temp is not rising and I am showing water exiting the exhaust so I ran for about 10 minutes with no over heating in anyway...
looks like Fay is going to hit us, the only question is wether she will be a tropical storm or a full blown hurricane.:smt089
So with that said whats on you're prep list.
I started yesterday with firing up the generator to make sure it works and loading up on 26 gallons of gas in my gas...
So I was doing some maintenance on the boat today and tried to run the bilge pump to get some water out and it turns out to be DOA.
it's a Rule 1100 GPH.
So here's my questions.
1. Since it failed should i upgrade to a higher capacity pump? not that the existing one didn't work, I just...
after finally getting over a cold that lasted 3 weeks I finally made it out to 1 mile reef for an open water dive. it seemed like a nice spot, not to far off shore and only in about 24 feet of water so I though I would pass it on to anyone who might be interested.
I used the following...
Background :
I'm noticing that my belt is starting to flake off some of the rubber pieces and I have loosened the tension pulley and removed it and restored it with no problems. Blets 4 years old now.
I called up Marine Max and gave them my engine serial number OM670xxx and my information ie...
4th of july is just around the corner. what are your plans and where will you be.
For me if I can shake this cold that I caught at Weeki Wachee last weekend. I will hopefully be making a dive off Anna Maria early in the day followed by some lounging and possibly some grilling out at Egmont Key...
So I got my PADI open water cert last weekend and am now dying to go diving. anyone have any good recommendations on spots that would make for some good initial dives.
I'm looking to try and stay in about 50ft for the first couple of dives before i go deeper and would like some recommendation...
this past monday I spent the day ducking between rain storms as I ran for home some 120 Miles up the Western coastline of florida. I would have been clueless as to what was going on around my had I not had the following website's programed into my blackberry.
http://www.ssec.wisc.edu/data/paw/...
I've been wanting to get a grill for the boat. I don't grill know but have brought some stuff that I can warm up on the stove. $99 seems like a good deal, but I don't know if I should spring for the Version 2 which is $120 more.
any input would be appreaciated. note is would be ued...
Just got off the horn with MM clearwater to sign up with them for the fathers day getaway. Anyone else going on this getaway.
I've vacationed a couple of years down in Captiva, but this will be the first time I go via boat.
I wanted to post this theard out to seem any of you will be on the water this weekend. I haven't decide yet if i'll be back on the water this weekend or not as holiday weekends like this bring out all the idoits; but if enough folks are going to be out it might be worth getting together...
So I completed the install on my 545s on the top of my helm with it recessed just under the wind screen so as to prevent from taking a direct hit when I take a wave over the bow ( yes it has happen in the past):thumbsup:. Now sice my GPS76 has always been so accurate. I assumed that the NEW 545s...
Just got the boat back in operation state today after needing a new fuel pump and so I go out to fill my gas caddy and I see all the gas stations in the area have Ethenal 10% blend stickers on them.:smt021
I had to drive around to find one that did not. I an very upset....
has anyone in FL...
Has any one swapped their factory SmartCraft thru hull transducer for a Garmin one? I'm looking for any input tips or tricks....
how hard would this project be knowing that my boat is on a lift and I can get up under it pretty easily in my inflatable?!
thanks in advance.
Anyone know of a local carpet shop that does snap in carpet. I want to avoid having to send my carpet out to be done and know I would probably get a better price locally.
heck I know I can get the carpet from Home Depo/Lowes just need someone to doe the binding after I cut it.....
So here's the idea. MM is having their new owners getaway to Caladesi the weekend of the 17th. I'm in need of a getaway weekend. anyone else insterested in crashing the party :grin:.....
So I pull the carpet yesterday out of the cockpit and good amount of the backing is glued to the cockpit sole. Any one have a good way to get all the black guck up with out spending a couple weeks scrubbing inch by inch. it's real bad....HELP!!!!!!!!!!!!
So I'm out on my dock today and I notice an oil sheen under the boat ( Boat is up on a cradle lift) . kind of like a drop of oil. I go aboard and notice that my drive oil resevoir is Empty, not just low but bone dry!!!.
so been check the manual in preperation to check what the heck is leaking...