Search results

Hi all: I am a MarineMat dealer/installer in the Tampa area. I now have templates drawn for the following SeaRays: 1998 - 2002 310DA, 1999 - 2002 340DA, 1999 400DA (upper & lower). I can offer much better pricing on these models than you will find on websites. We can do teak look or select...

This is a recommendation based on my experience. I replaced my manifolds and risers on my 350 Mag MPI's three years ago. I decided to try GLM based on their pricing. The old Mercruiser parts were 8 years old and upon removal the showed no signs of failure so this was strictly preventative...

I have an unusual problem (I think). Its a 2002 310DA but the same ShurFlo set up as ususal. I have very little water pressure on the hot side. When I turn on the faucet I get a burst of pressure which then turns into very light flow and then a trickle. I thought it was an air pocket in the hot...

I have a 2002 310DA with 350 mag mpi v drives. Boat has been idle for 3 months. Turn on ignition and no warning horn sounds. Also no audible fuel pump pressure up. Engine cranks won't start. Same situation for both engines. Turn starboard ignition on and the auto fire extinguisher light goes on...

I have a 02 310DA w/ twim 350 mag mpi & vdrive. Two weeks ago the boat ran fine, a little stumble here and there but it cleared up & ran well for the last 1.5 hours. Last weekend the starboard engine would not go over 2300 rpm & consequently wouldn't plane off. Nothing was added, changed or done...

I replaced the Clarion radion in my 310DA with an Alpine CDA 9884 primarily to be able to access iPhone music. To do it I cut a faceplate out of brushed stainless to hold the radio and cover the old CD changer hole. The mounting holes line up so I can reinstall the old set up if I need to. I...

Hi: I am offering waterjet fabrication services to CSR members, for their own boats, at my company's cost to do it. Search "waterjet" in the advanced search field to see the post. 'Thanks!

I replaced the Clarion radio & cd changer with an Alpine unit. I made a new face plate that attaches to the existing panel so that I could re-install the old units if I choose to. I cut the new face plate out of brushed stainless on a waterjet. I also cut a hole to accomodate the iPod / iPhone...

Hi all: I posted a message a few days ago offering waterjet cnc services to CSR members for their personal use. To view it search "WATERJET" in the advanced search field. Thanks!

Hi All: I would like to offer my fellow Club Sea Ray member a service. I have a 2002 310DA and have made a number of modification on it. I have the benefit of owning a company that does Waterjet cnc cutting. I would like to offer this service at my cost to Club Sea Ray member for their own boats...

Hi all: I have a goofy question. I usually don't use a pump out station for my head. I pump overboard. Don't be grossed out - I go out about 5 miles to do so. I tries to use the pump-out at the marina yesterday and the hose began to drain it out , but only a few ounces passed by the window &...

Hi all! Two questions for you all. 1. I have a Perko navigation/anchor light up on the radar arch - two 31mm festoon bulbs. Has anyone replaced those bulbs with LED's yet? Its very tight and needs a wide pattern. I saw one person selling the bulbs on ebay for $25 each but for $50 I'd also...

Hi all: My 2002 310DA gets about .6 mpg. It holds 200 gallons. Marco Island to Key West is 100 miles +/-. Anyone have experience in a similar boat doing this trip? Suggestions?

Now that I replaced the duckbill valves and survived without being esphyxiated or catching leprosy I am considering tackling the holding tank sending unit problem. The sending unit goes in through the top of the holding tank. There is about 6" of space in between the top of the holding tank and...

Well the vacflush vacuum pump started to take longer to buils up vacuum and it cycled at night signalling a impending problem. Proactively I replaced the duckbill valves and pump body orings (because I of course dropped one in the water). I reinstalled last evening in my 2002 310DA which is yet...

I have a 02 310da. (vdrives & westerbeke genset) I had to replace the battery charger (again). The new Promariner is a little different and they recommended upgrading to a 30A 3 bank. After installation the "#2 converter" breaker kept tripping after a few seconds. After a while,trying to isolate...

Hi: Does anyone knowhow to remove the cloth covered interior speaker grilles. They are mounted next to the V berth mirror in a 02 310 DA but I see thay have been used in many applications. (I searched for this and couldn't find anything - I know some of you get upset with redundant inquiries)

Well another Fourth of July fireworks cruise was survived. It really rivals the wild wild west here on the gulf coast of Florida. At least until we arrived back at the dock for the night. We are a 2002 310 DA with a Cruisair A/C-Heat unit with SMX II. When we got back the fan came on and...

Ive been looking for a replacement wood table for both the dinette area and the cockpit of my 310DA. Me dealer tells me that they cost about 300 - 500, which doesn't sound too bad (in Sea Ray dollars) but he needs an application to quote an exact price. So I need an inddor use and an outdoor...

I would like to replace the tables in my 310DA with smaller wood tables. I'd like them to match the sea ray cherrywood interior. Any suggestions on where to get them. I'd like them to be about 28" x 18" oval but dimensions close to that would be fine. Thanks!