Search results

I had family in town and they wanted to go out on the boat. It had been a while since we had taken it out so I put some muffs on it and ran it at home for a bit. Everythiong was fine on the dash but the water pump seemed to be making noise. We took it out anyway and to no surprise we over...

I want to remove and paint the emblems on the side pocket panels of my 210 sun deck but I'm not sure how they are attached. I don't want to pry to hard on them and snap them. Has anyone removed the emblems before?

Who's tried them and what did you think?

It looks like I need a new starter so I started searching the internet for one. It looks like I can get it cheaper from Amazon, but I feel bad not supporting marine suppliers. I feel like the $5-10 dollars more through a marine supplier just makes more sense in the long run. What are your...

My bracket on my 2000 210 Sun Deck has become fatigued and bends when you close the hatch. Has anyone had to replace this and where did you get the part from? I have done a search for the part number and part name and not finding the Sea Ray part. 634550 BRACKET, SS GAS CYL 90DEG L-BRKT...

My Shurfo 8050-224-133 bit the dust today. The pump is rated for 1.6gpm at 30 psi. The closest I can find is a 60psi. Will that be ok to use?

So after 3 months I finally got my boat back from having the lower shift cable, gimbal bearing, u-joints, coupler, bellow, and impeller replaced. I tried running it on muffs Saturday and it wouldn't start. I found the mechanic knocked the coil wire off. Once I got it back on I ran it for a...

I am going to rebuild my trim cylinders and the bag of parts shows one more o-ring than what Mercury calls for. Per their parts listing there should be 6 o-rings but there is 7 in the bag. Thoughts?

This weekend I went to lower the drive unit and it didn't go down. I tried pulling on it as someone pressed the button and nothing. I figured the cylinders were frozen. I took them apart so I could rebuild them and found water had gotten in and now the fluid has that milky look to it. I was...

I spend all day in front of a pc and I have to be honest due to the type of job I have I can surf the net a lot. I just ran across this group yesterday and already saw some upgrades I will be performing. You Sundeck guys might want to check it out...

I remember someone a while back looking for a plug the the cooler in the step of his Sun Deck but didn't know the size. Has anyone found a plug for the integrated cooler in the front step?

So this weekend I slipped and broke a plastic connector on the throttle body of my engine. I went to the Mercury site and got the part number and began my crawl of the internet. I was lucky and found one site that still carried the part. Every other site I went to said it was no longer...

Everyone here has been great in helping me find answers to my questions and I am going to you all again with another noob question. I had to pull off a riser to replace my steering cable. Now that I am going back together I need to replace the gasket between the manifold and the riser and mine...

Since I had my flame arrestor off while doing other work I decided to clean it. There was a sensor on the side of arrestor and when I took it off to clean it the tip of the sensor crumbled. I have been looking all over the place for a new one and can't find the part. My engine serial number...

Been looking but unable to find a wiring diagram for my 2000 201 SunDeck. Does anyone know if Sea Ary ever published wiring diagrams for the public or is it only shops that access to them?

Last weekend I got the old Clarion head unit and remote pulled out and got my new Boss head unit mounted. I hope to get it wired in this weekend and then it's time to install the new speakers. I'm going with Boss MGR350B head unit and Boss MRGB65 speakers. Has anyone installed speakers...

This weekend I tried removing my steering cable. It seems to me there is a sleeve coming out with the cable and I don't have enough room to get the cable out with the sleeve coming out. I have tried pushing the sleeve back in but that was a no go. I was afraid to put something on it to try...

I am in the process of refinishing my dash panel and since I had the gauges out I wanted to do something with the 3 gauges I have that are clouded up on the inside. I tried making 2 small small cuts on the back side if the bezel in hopes of being able to bend it enough to get it off the gauge...

When I bought my boat I put my registration number on with temporary decals. I now want to put on numbers I like but I can still see a shadow of the numbers from before I bought the boat. I already tried the Starbrite Premium Cleaner Wax and that didn't touch it. What do you guys recommend?

Ok guys looking for some more help. My dash panel is cracked/broke and the fake wood grain looks like crap. Looking for suggestions for how to repair and what should I do to refinish the panels. I thought about a carbon fiber sticker, but was afraid it wouldn't hold up. So then I figured I...