my windless seems to not have much power. Pulling up it struggled not under a big load and then stopped. Motor wasn’t hot amd solenoid just clicked. Waited a few minutes and finished bringing it up. Ideas on 1/2 power and stopping half way?? Thanks!
I am looking at the new complete kits: Quicksilver number
817275Q05 and I am seeing they went back to the 3 seperate plate/gasket pieces and don't have the single molded plate gasket anymore. Is that true or are the kits I am looking at older stock items?? The last kits I bought had the...
My local canvas shop didn't have black and can order but I was wondering what people use on the poles to protect the glass. Looking for black. I've seen stuff that's like a felt like soft material with a strip of Velcro.
Sent from my iPhone using Tapatalk
I was looking into the SEI water pump kits for next time. Complete water pump kit with housing is 1/2 the price. Anyone use them? They are for Mercury alpha one version too rt? Parts aren't just for SEI and interchangeable.
Sent from my iPhone using Tapatalk
Sent from my iPhone using...
I'm doing lower cables and was told to do the shift rod bushings and seals as exhaust water could seek thru and into shift cable cavity causing corrosion. My ?? Is has anyone done them and do I pull out the seal from bottom and just tap bushing out? I ordered the kit but was thinking just doing...
Bilge was dry all year and wasn't a lot of water but still there. Drive u joints has a little rust. I'll remove that but he bellows looks new still. Maybe poor seal? How would I know where it came from? No dry rot on it and I can't see any holes. Am I stuck changing it again? Not sore when...
Pretty sure it's a no but when filling manifolds with antifreeze can you fill too much and have it enter the engine when it gets to top of riser? Engine is off so no exhaust pressure. What stops antifreeze from entering engine? Should I fill until I hear it exiting exhaust in the outdrive? I...
Boats been fine all year. Maybe grinded when engaging reverse couple times but always seemed fine. Was fine last trip and today I went to run engines and spin props and reverse just grinds. I think I see I can make some adj on the lower cable on the bracket but seems odd. Any input?
Sent...
On my boat when the cabin reaches the selected temp the pump stops but the fan stays on Is there a setting where fan shuts off so it's not running all the time? I thought about leaving the a/c on all summer but don't want to have the fan running all the time so I only run it when I'm at the...
I'm going to remove them this year and I usually stuff a bag or plastic over it. Should I throw a packet of silica gel in the housing to absorb moisture?
Sent from my iPhone using Tapatalk
I had that on my center speedo gauge but not anymore. Don't see the option in cal 1 or 2 mode. What has to be on for this to come back?
Sent from my iPhone using Tapatalk
Initial run today and speedo read 4 mph but when a start to turn right it jumps up. Maybe some outdrive paint buildup in guessing. I hooked it up and locked the clip. Alpha One drives. My center gauge says mph pitot. I didn't have my GPs installed and I know there's also an option for gps...
Put away last year and idle pressures were 45 psi. I changed oils to 20w50 Royal Purple. One was 45 and other was 35 at idle. Both are good but wonder why one is now 10 psi less. Yes I winterized correctly and I did change oils and it is about 50 degrees today. Maybe 1 doesn't like the grade I...
I'm striking out with days to get this done and this week it's going to be in the 60's but showers at night. If I paint early I should be fine of a little rain happens at night right? Hydrocoat being used.
I found out why my antenna wasn't working. Cable was cut. I put a 2 ft cable on antenna side just need to splice a male and female on the broke end to the new cable. I need a couple ends and the splice tool. Any ideas? Seems pricey for the tool online
The gelcoat in the bilge has some cracks in it and was wondering if anyone used plasti dip in the bilge. Seems like a good product for anywhere or is bilge paint better