Search results

Does anyone know how to remove the radar monitor from the dash of a 410 sun dancer. I know their has to be a proper method for this and any help would be appreciated? I am replacing the R80 pathfinder with a R80 pathfinder.:smt100

WTB a cockpit cover for a 2000, 410 sundancer. Call Gus at 402-677-1456.

My starboard engine at higher RMP is overheating,and if I bring the RPMs down around 2200 the temp will come back down. I have replaced the sea water pump,the thermostat seams to be fine and my mechanic says my water flows are fine. He says now the next step would be to remove the heat exchanger...

I have a 2000 410 dancer with twin 454 mpi 380 hp gassers. The starboard engine has a slight rpm intermitant drop of maybe 100 rpm or a little more. Just enough to make my sync gauge jump around, and you can feel it if you are paying attention. When I throttle up real slowly it is not as bad or...

I have a Tridata ST60 system on my 2000 410 dancer. When I read the the water temp. it is in celcius and I would like it to be in fahrenheit. Does anyone know how to change it over? I would appriciate any help. Thanks again in advance. Beachnut:smt100

The previous owner of my 410 replaced the wood grain panels, where the insturments and switches are (in cock pit). The problem is that now they don't illuminate at night (gauges do but engraved labels don't). Does anyone know what could be wrong? Your help is always appreciated. -Beachnut

Looking for a cockpit cover for my 2000 410 sundancer, I think this models cover will fit from all of their years of production 2000-2003.

If their is anyone who has or knows of a cockpit cover for a 2000 410 for sale please contact me. Thanks Gus aka Beachnut

Can anyone tell me the easiest way to verify the hp output on my 2000 mercruiser 454 mpi engine? I just had a starboard engine rebuilt and the rebuilt one is producing less rpm's than the old one. Will the computer they hook up to the ECM on the engine tell you that info? Any information would...

I just had a starboard engine rebuild done on my 2000 410 da 454 mpi. Before I had this done the sync gauge would give me a steady reading with little effort. Now with the new engine the sync gauge is a little jumpy, especially over 3000 rpm. Can't get the gauge to stop moving even when I...

:smt101:smt017My 410 is powered by twin 454 mag mpi engines. I am topping out on my rpms at around 3900. I have read that I should be able to get in the mid to upper 4000s. Could this be that the boat is propped for salt water ??? I got it last fall in Florida and moved it to fresh water. The...

Cockpit icemaker does not work very well it will make one tray of ice when I turn it on after about 2 hours. And then it leaks in and out of the ice bin and then freezes. What a pain! Does anyone have any ideas on how to correct this problem. Most people I have talked to say get rid of it...

:smt100In my 2000 410 da I have 2 7.4 mags they both sound and proform well but the starboard engine after it warms up ,the oil pressure slowly drops from 40 to 20. So I changed the oil with 25/40 as recomended by merc. and the oil pressure then stayed at 40 lbs. for the rest of the day wich...

:smt100In my 2000 410 da I have 2 7.4 mags they both sound and proform well but the starboard engine after it warms up ,the oil pressure slowly drops from 40 to 20. So I changed the oil with 25/40 as recomended by merc. and the oil pressure then stayed at 40 lbs. for the rest of the day wich was...

Can a hot water heater be hooked to the gas engine in a closed cooling system antifreeze application too as well as the electicity? Gus

The system is making a noise similar to a dishwasher in it's wash cycle (kind of droaning). Just deweinterized and both forward and aft are doing the same thing independently as well as together. Could it be air in he lines? I opened the sea cock strainer checked if any debris and it is clean...

I bought a 2000 410 nov.2009 and was able to use it very little befor I had to winterize it. But I noticed that the vacuflush would not stop running most of the time unless I lightly touched the spring on the switch on top of the tank then it would stop. Some times until it was used again and...

I bought a 2000 410 nov.2009 and was able to use it very little befor I had to winterize it. But I noticed that the vacuflush would not stop running most of the time unless I lightly touched the spring on the switch on top of the tank then it would stop. Some times until it was used again and...

Does any one know how to change the screens in the port hole windows on a 1999 sundancer? Are the screen and gasket one peice? :smt100

Does any one know about changing trans. fluid in a 2000 hurth V drive ,and where is the filter located type of fluid , amount and aprox. cost and type of filter. The engine is a 454.