Official 330 Sundancer Thread

Does anyone know where the propulsion control module (PCM-09/ECM) is located on a 2013 330DA?
PCM09-300x282.jpg
 
Last edited:
Hey all does anyone have experience with converting the galley kitchen table to a sleeper on a 97’ 330? I’m going to dig around today and see if I can find any accessories/attachments. I’m thinking we don’t have the cushion but is there any hack to use or other accessories I’m not considering?
 
gater61 said:
Hey all does anyone have experience with converting the galley kitchen table to a sleeper on a 97’ 330? I’m going to dig around today and see if I can find any accessories/attachments. I’m thinking we don’t have the cushion but is there any hack to use or other accessories I’m not considering?
Click to expand...
Your profile says 98, your post says 97?
 
gater61 said:
Hey all does anyone have experience with converting the galley kitchen table to a sleeper on a 97’ 330? I’m going to dig around today and see if I can find any accessories/attachments. I’m thinking we don’t have the cushion but is there any hack to use or other accessories I’m not considering?
Click to expand...
Which layout do you have?
Page 14/7 or page 16/8?
 
Hello everyone. I have a 2009 Sundancer 330. Been having problems with my Generator Remote Start Panel. Last year the panel worked intermittently. This year it stopped working. Kept showing a “1000 ERR” code along with a loud beeping. Had to remove the panel board and pull the pin connector from the unit. This solved the beeping problem. I have always thought that the buttons on the remote panel were slow to respond or required multiple pushes to have an effect. The generator starts fine with the switch on the generator. It’s a Kohler 5ECD. The remote unit is a 3 inch round display. Looking for best place to replace the remote unit or any ideas on fixing what I have if that is possible. Thanks for any help or ideas anyone can provide.
 
Reddog said:
Hello everyone. I have a 2009 Sundancer 330. Been having problems with my Generator Remote Start Panel. Last year the panel worked intermittently. This year it stopped working. Kept showing a “1000 ERR” code along with a loud beeping. Had to remove the panel board and pull the pin connector from the unit. This solved the beeping problem. I have always thought that the buttons on the remote panel were slow to respond or required multiple pushes to have an effect. The generator starts fine with the switch on the generator. It’s a Kohler 5ECD. The remote unit is a 3 inch round display. Looking for best place to replace the remote unit or any ideas on fixing what I have if that is possible. Thanks for any help or ideas anyone can provide.
Click to expand...
You should add your location to your profile as there may be members here that are close to you and can help or at least make better recommendations for your area.
 
Can’t get power to both lower TV’s. 2009 330.
All breakers are on at main and all GFI receptacles I can find are on. Any ideas?
 
gater61 said:
Hey all does anyone have experience with converting the galley kitchen table to a sleeper on a 97’ 330? I’m going to dig around today and see if I can find any accessories/attachments. I’m thinking we don’t have the cushion but is there any hack to use or other accessories I’m not considering?
Click to expand...
Assuming you have the curved dinette:

Pull out the wood base from under the seat cushion. There is a plywood/melamine square brace with an u-shapes aluminum strip on it that slides under the base to support the middle.

There is a curved long crescent shaped cushion that on mine is stowed In the storage under that seat. It fills in the curve area and has Velcro on the back to hold it on the base. Then you pull out the two lower back rest pieces and they fill in the outside to make it a full mattress.
 
As a follow up I took a couple of pictures of the pull out berth setup. I am showing the support (not actually fully in place but just to show it) and the filler cushion that I mentioned above.
4A90A571-B6AA-451C-97A8-801D6010FCD5.jpeg
5D6EBE5C-1E6A-4D07-94C5-EC84EE10680B.jpeg
 
Has anyone experienced any "yellowing" on their exterior seat cushions in the areas where two cushions meet, like in the creases where the back cushion meets the seat cushion? In a recent seat cleaning I noticed a definite yellow/tan color in areas not exposed to sun. I'm assuming it might be an aging thing but it appears to be limited to the double helm seat and passenger seat next to it. My concern is that it appears to be spreading from the creased areas to the more visible areas of the cushions. I've tried various marine vinyl cleaners and some diluted degreasers but it's not had any effect on it?
Any ideas, suggestions, recommendations?
 
Looking for Props for my 1996 330 Sundancer. Can anyone please let me know what would be the best size and blade count. Thanks in advance. I have 1 1/4 shaft.
 
Bob Smiley said:
Looking for Props for my 1996 330 Sundancer. Can anyone please let me know what would be the best size and blade count. Thanks in advance. I have 1 1/4 shaft.
Click to expand...
I can't recall the details, when I owned mine I switched from three blade to four bladed made from Michigan wheel and it made a big difference
 
Hey,

To any owners of a 2009 Sundancer 330. Need to replace my window screens on the hull side windows. Four screens in total. Any ideas on where to find them if that is even possible?

Thanks!
 
Hello from Boston, we are thrilled to have just bought a 1996 330 Sundancer. She is in fantastic shape, but there’s much that I want to do. Quick question, is the fresh water tank on this boat visible in the engine compartment or it is it hidden, I looked quick and didn’t see it. I’m assuming it’s starboard side, since that’s where the water filler is? I also would like to know where the fresh water pump is to clean the filter. Thanks.
 
You must log in or register to reply here.

Forum statistics

Threads
113,182
Messages
1,428,056
Members
61,088
Latest member
SGT LAT
Back
Top