Search results

I sent you a PM- let me know your address via email.

I sent you a text message a while back and you never responded, but somebody else has expressed interest. Free for the cost of shipping.

I have the Lowrance 3500 display, came out of my 2000 Sea Ray. Just the instrument itself, no bezel, and one wire is cut withonly about 6 inches of extra. You pay shipping cost and its yours. I figure about $6-9 in USA.

Towing a Sea Ray 380 with a single axle trailer and a Smart Car. -- umm, did it occur to you that was tongue-in-cheek post from a troll ?

I didnt have to- I am already on R-dock.

if you can narrow down if its an upper gearcase or a lower gearcase that is leaking, you can just reseal that part. It sort of depends on how handy you are- I did them both on my Alpha previously: I dont recall the exact cost but a full seal kit is about $50-90 for the lower, somewhat less for...

hey Jim- sorry I stopped you on saturday when you were loading up the cart :) - Jon

It looks like NoDrog and I have the same boat as you: mine is 2000 270 DA. You have the extended camper canvas while I have the regular bimini canvas. If the boat sat for 5 years, I would strongly suggest replacing the raw water pump impeller before you take it out. They have a habit of self...

I had a guest on my boat, young woman who had purple hair highlights, and they got all over the seats. Nothing would remove it and I even went to the hair color manufacturer and they had a FAQ on the issue (alcohol was suggested) but that didnt work. But surprise- it faded away on its own in...

There is a product called Weld-On 4 and Weld-On 16 that are acrylic solvents. You could cut out and weld in a new peice, or glue something on top of it to reinforce the area. Search youtube for a few vids on acrylic welding

Who is the primary phone company that serves your marina ? PM me and I might be able to help you out with some ideas as I work for one of those telecom companies :) I was thinking that for the local marina the obvious choice is WiFi with a few repeaters: this can be provided by the marina to...

Exactly !! The Big Orange filter is also good: and Jack's filter kit is good as well. What impressed me about the Big Orange filter is that the guy obviously did his homework and the engineering is impressive. If you do not have a filter to start with, then the Big Orange filter is probably...

I sympathize- I had the same problem happen to me twice in the last 10 years. first engine I had to remove to get to the bolts, and wound up using many cobalt drill bits to remove them. There are tools similar to easy outs but they fit in the outside of the head bolt, IF you have enough room...

If you need to replace the existing filter as the carbon has worn out, you have the option of recharging the filter using a kit available on ebay for $23.99. It includes all the proper fittings, activated carbon for this particular application, special foam baffles. The instructions are...

PM with email sent: I appreciate the offer !!

I have done major exhaust manifold work on Gen 4, Gen 5 and Gen 6 454's and 502's, and they were all 1.25" long. The bolts are 3/8-16 threads. The last one I did to my sundancer, I used ARP stainless bolts purchased at 1.5" and I had to grind them down (mistake because 1.25 are commonly...

Teflon tape ? does it leak at the oil cooler end, or the oil filter pad side ? Keep in mind that the oil cooler is a small radiator: I have seen winterization jobs done where this was not properly drained or antifreeze sucked into the cooler, and caused freeze damage to the cooler.

I would advise replacing the manifold- The hard thing about replacing the trim manifold itself is the Mercathode electrode and the hoses: if you have the Mercathode you have to pull the wires just like the hoses. Find the correct part number and search around: I found the prices on that part...

What probably happened is that you have a leak of the trim manifold (part E), or the hose near the manifold. This exact same thing happened to my Bravo 3 last year (I think the manifold part numbers are identical to the Alpha Gen II but not positive). The illustration that Bt Doctor post is...

I tried calling Sea Ray Customer support on Friday- all of the numbers I found using web searches were disconnected. Does anybody have a recent customer support phone number ? Also, I think I found at least part of the puzzle: there is a large panel that covers the backside, which is going to...