rumrunner
Active Member
- Mar 27, 2007
- 417
- Boat Info
- 1996 33 Searay Sundancer
- Engines
- Mercruiser 7.4 MPI
Nice job sunsation! Same question as above. The the weather has been I may have some time on the hard to do more projects!
Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature currently requires accessing the site using the built-in Safari browser.
Creekwood, I'm new to the group...I have the same dinette set up that you do...you mention the wooden extension that pulls out, I've got that...then you mention a wooden support, not sure what that is - will you elaborate
I have found that the small aluminum pole works on the cockpit table and I have a factory cushion that sits on top of the cockpit table with the small pole to create a "play pin" in the cockpit...if I use the small aluminum pole on the dinette it is too short...if I put the dinette table on the short pole it is too tall
I wish I had a picture and the boat is 2hrs from home. On the bottom of the pull out board there is a screwed on aluminum rail. Then stored in the under seat area is a white wooden square board about 3/4" thick, about 1 foot long with a rail on its edge that slides onto the rail on the pull out as a support. Its just high enough that it supports the pull out and long enough that it sits on the raised carpet area out to the edge.
Then the cushions from the backrest snap/velcro to the pullout to fill it in. I then put on a double sized mattress cover and sheets (helps hold it all in and suppresses that middle of the night "slide on leatherette" sound from waking everyone up.
Its actually pretty comfortable (and the shortest route to the head in the night), although at 5'10" I am about the height limit to be saying that.
I wish I had a picture and the boat is 2hrs from home. On the bottom of the pull out board there is a screwed on aluminum rail. Then stored in the under seat area is a white wooden square board about 3/4" thick, about 1 foot long with a rail on its edge that slides onto the rail on the pull out as a support. Its just high enough that it supports the pull out and long enough that it sits on the raised carpet area out to the edge.
Then the cushions from the backrest snap/velcro to the pullout to fill it in. I then put on a double sized mattress cover and sheets (helps hold it all in and suppresses that middle of the night "slide on leatherette" sound from waking everyone up.
Its actually pretty comfortable (and the shortest route to the head in the night), although at 5'10" I am about the height limit to be saying that.
There has been a lot of talk on this thread about trim tabs. My problem was that the actuators were mounted an inch or so too high, so when they were fully deployed they did not have much affect on my running angle. My solution was to fabricate and mount a spacer out of starboard (marine plywood). Here is a pic of the finished project. A 1" spacer mounted under where the actuator connects to the tab. I had to drill 2 new holes for the actuator to bolt onto the tab, but other than that it was pretty easy.
Thought you 330 guys would get a kick out of this "custom" hard top '98 330DA. I don't like the looks of it personally, but to each his own.
http://cgi.ebay.com/ebaymotors/1998...d8cQQitemZ280676212108QQptZPowerQ5fMotorboats
Thought you 330 guys would get a kick out of this "custom" hard top '98 330DA. I don't like the looks of it personally, but to each his own.
http://cgi.ebay.com/ebaymotors/1998...d8cQQitemZ280676212108QQptZPowerQ5fMotorboats
On a side note I got out on a friend's boat tonight and caught the first Striped Bass I've caught in the last 10+ yrs... I've also had a bit of a fishing bug going lately and I was wondering has anyone mounted rod holders on the 330??? I'm leaning towards the rocket launchers that I can mount on a stern rail vs drilling holes and doing the thru hull rod holders. Any thoughts on this one would be appreciated. Thx
On a side note I got out on a friend's boat tonight and caught the first Striped Bass I've caught in the last 10+ yrs... I've also had a bit of a fishing bug going lately and I was wondering has anyone mounted rod holders on the 330??? I'm leaning towards the rocket launchers that I can mount on a stern rail vs drilling holes and doing the thru hull rod holders. Any thoughts on this one would be appreciated. Thx