Roch Speiser
Active Member
Nice!! Where and how much if you don't mind?Ordered a new 36" cockpit table. It's a resin product actually intended for outdoor restaurant use. The color matches my dash perfectly. View attachment 81178
Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature currently requires accessing the site using the built-in Safari browser.
Nice!! Where and how much if you don't mind?Ordered a new 36" cockpit table. It's a resin product actually intended for outdoor restaurant use. The color matches my dash perfectly. View attachment 81178
Here's the best part, it was only $91 delivered!!!!!! ebay link https://www.ebay.com/itm/36-Round-H...var=622097070281&_trksid=p2057872.m2749.l2649Nice!! Where and how much if you don't mind?
Wow!!! That’s incredible. Would love to see installed pictures once your ready. Thanks for the reply.Here's the best part, it was only $91 delivered!!!!!! ebay link https://www.ebay.com/itm/36-Round-High-Gloss-Mahogany-Resin-Table-Top-with-2-Thick-Drop-Lip/352814022928?ssPageName=STRK:MEBIDX:IT&var=622097070281&_trksid=p2057872.m2749.l2649
I just bought a $20 table base and screwed it on with 6 screws and ready to go. I did this on my sea ray 450 I had before this boat and got lots of compliments.
I am curious how hot it will get in the sun, looks fantastic!I have been all over the board these days with projects other than the boat but still isolating as per Washington State requirements.
I did get the cup epoxied in for the Garmin Sonar Transducer and fished the wire. There were a handful of other items like the new cable for the davit system. The old one was galvanized (why?) and was rusted to the point of certain near future failure. I replaced with a SS cable.
The upholstery shop called and we were the last job out the door before they shut down. I drove down to Burien from La Conner, normally a 2 to 2:15 drive, in 1:30. Zippo traffic... I did stop by a buddy's place and pick up his cable crimper for the additional lift cable for the new Walker Bay I built up last year. It has 4 lift eyes vs. the 3 on the old RIB.
Got back by 2:30 and started the install. My wife came down and could fit under the benches by the ice bucket to get the washers and nuts on the studs that are on the backrest there. We were done by 5:30.
Then we were off to do a restaurant takeout that she organized for our Yacht Club. It is Dinner and a Movie supporting a local restaurant and Netflix Party. We are doing another run tonight and we are hoping to get 100 dinners.
Here is the helm:
Cockpit:
I have been all over the board these days with projects other than the boat but still isolating as per Washington State requirements.
I did get the cup epoxied in for the Garmin Sonar Transducer and fished the wire. There were a handful of other items like the new cable for the davit system. The old one was galvanized (why?) and was rusted to the point of certain near future failure. I replaced with a SS cable.
The upholstery shop called and we were the last job out the door before they shut down. I drove down to Burien from La Conner, normally a 2 to 2:15 drive, in 1:30. Zippo traffic... I did stop by a buddy's place and pick up his cable crimper for the additional lift cable for the new Walker Bay I built up last year. It has 4 lift eyes vs. the 3 on the old RIB.
Got back by 2:30 and started the install. My wife came down and could fit under the benches by the ice bucket to get the washers and nuts on the studs that are on the backrest there. We were done by 5:30.
Then we were off to do a restaurant takeout that she organized for our Yacht Club. It is Dinner and a Movie supporting a local restaurant and Netflix Party. We are doing another run tonight and we are hoping to get 100 dinners.
Here is the helm:
Cockpit:
Does the gen bog down when you apply a load to it? The governor may need to be serviced. I would check that first if it is running fine otherwise. Assuming you have a westerbeke with a mechanical governor.Thanks JZ, my wiring for the fridge was my first thought and he just called back and confirmed.
Yes, there was a 4 amp light in my eyes! I wired the fridge to the "stereo memory" and "bilge pumps" that are on the start side so they are always available...not matter what you do to the house batteries. He moved it over to a circuit that is on the house side.
Now on a separate issue and not related, the generator dips voltage and frequency when trying to run more than one thing at a time. AC charger, water heater, coffee make on 110AC plug or microwave. It does OK on just one of the above. Forget about the A/C unit. We tried to run for a little heat and it would not run.
What are your guys experience with the generators?
Thanks!
Looks great!Just got my new aqua marine decking installed. It’s the brown color with what’s called new teak design. View attachment 82542View attachment 82543View attachment 82544View attachment 82546
Would love to see pictures on how you mounted tv’s in cockpit and salon. How wired as well. I want to do tv on wing On helm and bulkhead in salon over aft cabin.Tons of more updating I'm doing on the boat include: glass door refrigerator in the cockpit, All new rockford Fosgate sound system, New tv's in cockpit and cabin (cabin tv moved to starboard side of cabin stairs), new memory foam mattress cut and fit, Raymarine Axiom and I70s installation, blue underwater lights, Aqua Marine Flooring installation on swim platform and full cockpit. all exterior badging switching to chrome,
Here's a pic of my new pinstripe finished and ready for launch. Very happy to get rid of the gold!!
View attachment 81554
Here's a picture of the new eva foam floor I put in the head. It's from Aqua Marine Deck. They now have the template from mine if you want to use it and save the hassle of templating..View attachment 81555