Search results

Chaz_360- I appreciate the write up. I ordered the windshield gasket from FP. Hopefully it will be warm enough to install next week! Thanks again, super helpful

I have a 02 360 and it’s been a great boat over the last 5 years. However, my center vent window is leaking pretty good when it starts to rain. Has anyone replaced the seal? If so, how and where did you get the material? appreciate the help!

Couldn’t get into our family island as the water levels dropped to much. One of our last few weekends anchored out on the mouth of the Doty and Sni.

I saw the Hardin option but went with mercruiser standard pump because my mechanic had one in stock and I had guests coming over so needed a quick turnaround. The new mercruiser pump looks like it has a wear plate in it. As far as the old pump, I had to apply a torch to the side and a couple...

When back in our marina from a couple days on Put-in- Bay. I went down into the engine compartment to just look around as we had a pretty rough ride down and back. I noticed a couple drops of water on my waste tanks vent filter and thought it was odd, stared at it a little longer and then...

Isn’t it raft off today? If so, probably patrolling.

Sorry for the multiple posts but just thought of another question on starlink. Probably a dumb one but, how far away can you get the wifi signal from your boat? Meaning if you tied the boat up how far away can you go before the wifi signal drops out. I have a semi remote cabin on an island, so...

I just purchased a starlink so I can work from the boat more often and have better quality internet for Vidoe calls. I’m looking to install on my radar arch. Do you guys keep your starlink plugged into an inverter or just restart it when you switch back and forth from shore power to genny when...

Got it. Looks good Thanks!

Can you post your starlink dish install. Looking to do something similar.

i have the Dewalt 20v fan as well for my cockpit. It obviously runs on a 20v battery so if not running the genny, it works and it’s super portable, while moving a ton of air. The nice thing about it is is if you have a small extension cord you can plug it into 120v wall socket if Im on shore...

I just finished up working with Starke products for my second year and still loved the outcome so I’m sticking with them as well. The only question I have is. On my top deck non-skid (diamond pattern) I have little black dots along the edge of the diamond. I tried a wool pad and heavy cut...

I have Raymarine Axiom chartplotters and used Fox Marine gateways to get my engine data to my axiom plotters. I have the same engines and same year. It was a simple install, ran a nmea 2k backbone down to the engine compartment and plugged the gateway into the engine port and then into the...

I used Starke products last year (Level R, Elevate and then the sealant Hyper Hold) and loved the outcome- I’ll be using Starke products again later this week as I kick off my annual buff and wax. I’ll probably not use Level R and will start with Elevate. I see you used ignition before hyper...

I’m 37 - been with my wife for 16 years married for 8 of them - ( I can’t believe she’s put up with me for that long) 3 kids with another on the way. Son who is 6, two daughters 3 and 1.5 years old and the bun in the oven is another daughter. All kids have been on the boat within their first...

Here’s a Canada crossing story, so of course 19 year old males living in metro detroit in the late 90’s early 00’s we would cross to Canada to drink at the bars legally, get wasted then drive back across the border back to Michigan. While one time crossing back from Canada sh*t faced, we pulled...

I agree with Craig, I have two 500 amp smart shunts installed one on each battery bank. I’ve never had an issue with my 8.1’s starting. I would also agree with some of the earlier posts that I wish they would connect to my axiom MFD without the added cost of purchasing something like a Victron...

Coming into this convo late but I installed an axiom mfd on my boat and was able to network the original st7001+ (If that’s what the OP has ?) to the axiom network. The axiom MFD and original autopilot talk to each other and I’m able to follow routes created on my MFD with the autopilot. The...

Blueone, pretty sure I saw your boat at the NCYC, last year, if I remember correctly, you where backed in along the North Channel. We have an island down from the club on the Sni. Anyway, if your looking for a dinghy ride to the new bar just take the canal between Tiki Toms place and Deckers...

I took our flat bottom over there back in November to scout it for my 360. I’m glad to see in an earlier post that they have permission to dredge and add channel markers. It’s definitely shallow leading from the bay into wall and the channel was marked with a couple pieces of rebar and a pop...