I have a 2009 Sundancer 330 with 496mags.
Starboard starter is starting to go and I need to replace it.
Looks really tight to get at the starter.
Can this be done with out removing the motor?
I have tried prying the panels but they are certainly anchored securely.
There is no way to get behind the port passenger side or port aft side on the arch without cutting.
The starboard side I can use use the access panel and feel around but not much use when I can not
remove the port panels.
I...
There are 4 cockpit speakers and 2 swim platform speakers.
To turn the swim platform and rear most cockpit speakers on there is a button on the left
side of the dash, above the navigation lighting with an audio type mark...press it and the blue button lights. This will turn off your rear sets...
I am trying to replace the 4 cockpit speakers in the cockpit of my 2009 Sundancer 330.
I have tried to pry the panels off covering the speakers with no success....fells like they will rip or tear..thought they may be on a sort of snap or something like car interiors but I am now starting to fear...
Have a similar issue with my 5ECD....with genny running the battery voltage doesn't appear
to change...checked the fuse #6 and it had blown...replaced and it still doesn't show any battery charging...
could be the DC voltage regulator??
Any luck with your issue?
Yes, Was aware of the 45 day validation and dealer id #..Just as you said I was hoping to find
an older version previous to the newest version 1.7 ........
Hi,
Yes the compass I can do myself without the software..just an example of what it could be used for.
I know that the software is expensive, but it is something I would like to have.
Hi all,
I was at the mercury dealer and he was working on my boat using Mercury
G3 software. He showed me the vast amount of things he could setup and diagnose
using this.
I contacted Mercury and they said that only dealers are allowed to buy this.
That is crap. My mechanic said that every boat...
Hi all...
I have a 2009 Searay Sundancer 330 with 496 mags DTS/Axius.
In the spring had both outdrives serviced with new oil/shift cables bellows..workd fine
until about a month ago...Noticed one day that the starboard motor was starting in
forward gear...This was a shock as I quickly shut it...
Hello,
I have a 2009 Searay 330 Sundancer with twin 496 mags.
Just launched the boat with fresh bottom paint, both props rebalanced and gone over...
I sync the motors and the port side engine reaches WOT at 4450RPM, when the starboard
side motor only reaches 4120 RPm..
The WOT range is...
FYI.. Good to know.....Figured it out...I had replaced the starboard side trim sender for the usual
analog display...nothing...then looked at the port side engine..unplugged the trim plug at stern and checked
the resistance..looked ok but when I put the drive up, the trim guage still moved...but...
Hello...
I have my starboard engine's drive trim guage and Vessel view trim display not functioning.
This is a 2009 Bravo 3 outdrive with axius/DTS.
I have replaced the sending unit but still there is no movement on my starboard trim guage.
The vessel view display doesn't show the drive moving...
Ok, Pulled the glomex antenna and tried a quick fix with another tv antenna amp...this still tripped the mdp breaker for the inverter...pulled the amplifier off and just left the
bare dc wires..get 12v off them but when I turn on the mdp breaker for the tv/12Volt outlets and then turn on the mdp...
I now have the culprit..It is the glomex antenna amplifier,not the tv, that is tripping the dc panel breaker...TV works fine without the tv breaker turned on in the panel..but as soon as you turn on the tv breaker
for the glomex antenna amp, the dc panel breaker trips...have to investigate further.