I am going to be selling my 50 ft Sundancer and I am posting to see if anyone has a use for the lift. It can fit any boat up to 15 foot beam. My boat weighs around 50,000 lbs. It runs on hydraulics and is maintenance free except a grease gun once a year. I have been lifting my boat for 4 years...
I have Cat gauges for sale that I removed from my boat. The pictures are in the Installation/mod section. Contact me if interested. They are for Diesels.
I have all the switches engraved and backlit with a dimmer. The gauges are also hooked to the dimmer and are backlit with blue pointers. Took a while but it is about done.
:huh:Does anyone else do any boating north of Beaufort, NC? I do quite a lot around the Pamlico sound out to Ocracoke and venture up to Manteo now and then. Every third Friday in Washington, nc they have music in the streets thats fun to bring the boat to. Looking for any other spots on the...
Can anyone help me with a source to get the cabin door seal that fit into the dovetail grooves on a 1996 50ft. Sundancer? The manuals do not show them, the manufacturer of the doors says they are obsolete and cannot help. I have posted the question to "Ask a SeaRay Employee" and have not heard...
I have my current 1996 50 ft. Sundancer and have exhausted all sources for finding the seals that are on the cabin entry door. The ones that are in there are original and in bad shape. They slide into a dovetail groove on the sides, top, bottom and between the bi-fold to keep water out. Can...
I have a 1000 GPH 230volt circulator pump for a a/c system. It came out of my 50ft Sundancer. It does work well but has some rust on the motor end (cosmetic but still works great). It was servicing 3 a/c units. $200.00 takes it. It will be going on ebay soon for 275.00.
Here's a couple pics of a lift I finished up last fall. I use hydraulics and it takes about 45 seconds to lift 8 feet. Boat weighs about 40,000lbs when loaded up.
, Not sure if this works, 1st try
Hello, Has anyone rebuilt the Sea Star HC5801 Steering cylinder? It hase a smaller cylinder attatched as well as a power assist unit all mounted as one unit. I can't even find a seal kit for this unit. I did end up putting a new unit on last weekend and would like to repair the one I have for a...
Can anyone use these items? I will let you have them if you can use them. I removed them from my boat when I purchased it and replaced everything. The head unit was bad and the previous owner said these were still good. It was an older stlye head unit and I didn't want to go thru the hassles of...
I have noticed that my shaft has slid out of the coupling about 5/8". It is a solid coupling. it does not have a visable cross pin to hold it in the coupling but does have a hole that you can see into. it almost looks like there is a step turned on the shaft so it cannot come out of the...
Ongoing problem with lots of smoke and no power between 1100-1400rpms untill the turbos kick in. Mechanic told me to check the waste gate. I cannot even find it in the manuals. Does anyone know if this is on a 1996 year 3176Cat engine? If so what does it take to check it out? Thanks for any advise.
I had the boat out today and when I went to take off it would not get the rpm's up and black smoke was comming out bad. Eventually it did come up to speed, cleared up and ran fine. It has new fuel filters. What causes this? Any ideas would be appreciated. 3176 Cats
Can anyone help out with how many, where and sizes of zincs on the 3176's?? My manuals say there are 3 in the heat exchanger and 1 in the elbow. I did find a cat part number for the 3 in the exchanger but it did not list the one for the elbow. I believe the 3 are 1/4" pipe plug with a 3/8...
Can anyone tell me what size micron element I should use in 3176 Cats? I have 2 Racors prior to the secondary spin on that is mounted on the engine. They come in 30, 10, and 2 micron. Is the first a 30 and then a 10 or both 30? Or both 10? Thanks for any help.
I have just purchased this boat with a B & G Network electronics and the autopilot holds a straight line when cold and after about 15 minutes it will only work about a minute or so after being set again. The unit says rudder drive fault and the manual from B&G says to check the connections. I...