Hello,
Excellent job installing the Allure Ultra flooring!
I am also considering installing the same flooring in my "02 340 Sundancer.
I have a few questions I'm hoping you can answer.
1, What effect does extreme cold have on the flooring? Does the floor show any signs of contracting and...
I have the same issue on my Starboard 8.1L Horizon. Here are some parts have I replaced that did not solve the issue. Hopefully this can save you some money on parts.
Both high and low pressure fuel pumps and fuel cooler. Also changed both in-line fuel water separators, and swapped out relay...
Hi,
I was reading your post, and am having similar stalling issue on my starboard 8.1 . Although I have the Gen2 cool fuel module. Mine stalls at both harbor and also when getting on plane. What exactly did you do to bypass your solenoid? I only have 1, just out of the tank.
Thanks, and good...
I am having a similar problem on my 8.1 starboard engine and I have measured the fuel pressure on the Schrader valve on the fuel rail. Mine was reading 35psi, and the specs I believe are 40psi +/- 2psi. That may have something to do with the issue. Are you stalling at harbor speed (lowest...
I have 2 issues with my unit. 1, The right half of the screen cannot be seen. So it is impossible for me to scroll through the screens to set up the unit as a slave. 2. My unit is frozen and will not cycle or power down. I have to pull the power plug from the back to power down. So I am not even...
I had my boat winterized from a local marina in the fall. I just launched the boat, and my impellers are not pumping any raw water. )Luckily I caught it right away before overheating the engines). The impellers are paractically brand new last year with about 15 hours on them before the boat was...
I will check into that also. My drain plug is not installed so it could have possibly leaked out of the bilge into the gravel where my boat is sitting>
Ok, I am stumped on this one...I had my Merc 8.1's winterized by a local marina where I store my boat. I have closed cooling on both engines. I have just noticed both coolant reservoirs are empty, as I was getting the boat ready to launch. Both reservoirs were full when I drove the boat there to...
Hi Mike,
Not sure if the mic/radio is still available (can't tell from the latest replies) If it is available, I am also interested. I do have the 210 model also.
Thanks!
My ST60 Tri Data Depth readings seem to be somewhat accurate when under power, but when moored in my well show at least 15 feet deeper than actual water depth. Anybody else ever have this issue? I am not sure if it is the transducer, or the display causing the issue. I believe my transducer is...
1, My Raymarine RN300 GPS unit display screen (right half of screen) is not displaying at all. The unit is fully operational. It is an lcd screen, so I tried to gently press on the screen to see if there was possible a loose display connection, or if the unit or screen/housing was warped, but...
No in line filter between pump and carb. When I disconnect the fuel feed at the carb and manually run the fuel pump the fuel flows freely. I placed a container to catch the fuel coming out of the fuel line to verify this.
I will try that. I did move the float up/down when the carb was disassembled the first time, and the needle valve appeared to be moving freely. I will dis-assemble the needle valve this time and look for obstructions. Thanks Ken.
I removed the top section of the carb and verified there was fuel in the bowl of the carb. I don't know what the proper level of fuel was, but the bowl seemed to be about 1/2 full of fuel. I also removed the fuel supply line to the carb, placed a container under the fuel line, and manually...
My Westerbeke generator will crank but will not start. If I prime the carb it fires up until the prime is used up.
I pullled supply line to carb and fuel lift pump is working. I also pulled off carb and cleaned and looked for blockage, but it looks ok. I also verified there is no fuel coming out...