Search results

Hi all, Feeling a bit silly, but for the life of me I cannot figure out where the 4th blue drain plug gets inserted on the engines. (I didn't winterize.) For reference, I have twin raw water cooled 5.0 MPI DTS Bravo III. I found 3 of the locations on each engine, thermostat housing, the...

2010. 310 Sundancer Twin 5.0l….the issue I have is a ground wire that is fastened to a bolt directly above my garboard drain. I thought the ground wire looked a little loose so I attempted to tighten the nut but the bolt was just spinning. Turns out the bolt broke off the head. Does anyone know...

Has anyone ever had the glass in their windshield slide out of the groove? I’m not see ally sure how to slide it back in and am scared I’m going to crack it. It appears to have shifted 1/4” or so. The boat is a 2010 310 Sundancer

My boat has 1 CO2 Detector and I have the relay setup as I have a generator on board. My CMD4 has reached its end of life. I have just received my new detector and am a little confused as how to wire the new one up so I'm hoping for some CSR guidance. Obviously the black and red wires...

Apologize in advance if this question has been asked... I just purchased a 2010 310 Sundancer that has 5.0L mercs with DTS and vessel view. Last fall the previous owner installed brand new pretty cool Simrad chart plotter. I don't know jack crap about these things, but I am wondering how I...

Where could i find information that tells me what my Water PSI on my sea water pump should be at say 3200 -3800 rpm? I run a 350 MAG with Seacore and can not find this information in my manual. I just replaced my sea water pump assembly due to a bearing failure, so i want to be sure everything...

My vacuflush 1/2 full sensor continues illuminate on the panel even though there is nothing in the tank. I just pulled the sensor stick out of the tank expecting something to be impeding the float slide. Nothing is there.. Regardless, I cleaned it really good put back in there and it still is...

underneath the sink in the cockpit wet bar sink bowl there is a black plastic piece that connects the drain to the overboard discharge hose. Unfortunately mine has cracked off and broke. The best way to describe the part is that is a black, hard plastic funnel looking thing. it sits at very...

Struggling here... I have had issues with my Vacuflush system basically for 7 months now. Last weekend my vacuum pump would continuously run and the toilet had no vacuum to flush. I have had issues with the pressure switch before so I fiddled with that but had no luck getting the pump to stop...

Hi All, I have a SeaCore Engine/Drive Combo which according to my Sea Ray dealer is in need of new anodes. I was told by them that the SeaCore drives have anodes on them that are specifically designed for salt water. Since I boat exclusively in fresh water is there a different material of...

Does anyone know the where I can get the correct elbow fitting for the Dometic AC water pump? The model I have is PML 250. I believe I need a 1/4" female to 1/2" barb combination elbow. I can't seem to find one.

I have been boating for a long time now, and I knew at some point this day would come. Yesterday we lost our vacuum on our vacuflush unit. (model is 28HTS - VG) My first thought was that it was clogged, but last night I basically tore the whole unit apart and everything looks just fine, all be...

This weekend while trailing my wife and i came up on some unexpected highway chip seal repair work. Unfortunately we were too far into our trip to turn around and take a different route. I have a blue hull 240DA and now have a whole bunch of tiny rock chips down the side of the hull. Does...

Hi all, i have a slow leak at the faucet in my Head. I need to replace the hot water cartridge but can not for the life of me figure out who manufactuered the faucet. The Searay Parts guide tells me it is this: 1772520 FAUCET/SHOWER, BRUSHED NCKL/CHR PULLOUT I think its the same...

I am just wondering if anyone on the forum has one and can offer some feedback regarding its preforamance/handling/comfort. etc. There doesn't seem to be a ton written about these boats. My wife and I are toying with the idea of moving up slightly and we really like the side entry option with...

I am wondering if any of you guys with 2006 and newer 240 DA's have installed the SeaDek swimplatform mat on your boat. On SeaDek's website they have a template for a 240 DA with what i think is the swimplatforms.com extended platrom included. I have the extended platform on my boat as well...

My microwave is broken. Its the old Sylvainia .5CF model that is not made any more. I rarely used it so I am thinking about taking it out and using the space to make a small storage cabinet with a shelf that could be used for dinner plates/bowels and breads. Has anyone done anything like this...

I am running 3 Optima blue tops, (2 house and 1 starting) and wanting to add one more. (3 house and 1 starting) My reasoning is that i want to add some more speakers and an additional amp to my boat. I have been told that the factory Alternator will have trouble charging 4 batteries. Is this...

I just unloaded my new swim platform off the truck today.... Tomorrow i will be installing it. The instructions call for 10 holes in the back of the transom... Fun times!! Wish me luck

My wife and I are expecting our first child sometime in late april. Obviously a life jacket is in order, can anyone recommend a jacket that works the best? Normally our boat splashes for the first time in very late april, but this year i would imagine boating will be pushed back a little. It...