Official (1998-2002) 310 Sundancer Thread

HELP:
Does anyone have the exact cabin below table dimensions 2002 310 ???

Also looking for a new switch panel alone , GAS, Burl color....
 
Last edited:
For the switch panel try flounderpounder they make replacement switch panels the table I have an 01 if it's the same I can get you the dimensions in a few days
 
I'm installing a raymarine radome on my '00 310 next week. Also upgrading to the new a97 mult display. Any tricks/issues I should be aware of with running the wire in arch, etc??
 
Sal A said:
For the switch panel try flounderpounder they make replacement switch panels the table I have an 01 if it's the same I can get you the dimensions in a few days
Click to expand...

Sal, thank you...when ever you can. yes there the same table....i e-mailed F.P. to see if they would sell me just the panel....
Not the whole set...

Thanks Again....look forward.... Bill
 
Np bill I'll get it to you ASAP ! I'm out east if you wanted to take a ride your more then welcome to bring some cardboard and use my table as a template !
 
Sal A said:
Np bill I'll get it to you ASAP ! I'm out east if you wanted to take a ride your more then welcome to bring some cardboard and use my table as a template !
Click to expand...

Thanks Sal....OK....Only if its convenient for you , then ill take a ride.....Appreciate.....:)
 
Last edited:
I'm in east Marion it's the town past greenport


Sent from my iPhone using Tapatalk
 
Bill tomorrow I'll try and get up in the boat I'll make a template of the table you want the one in the cabin correct


Sent from my iPhone using Tapatalk
 
Sal A said:
Bill tomorrow I'll try and get up in the boat I'll make a template of the table you want the one in the cabin correct


Sent from my iPhone using Tapatalk
Click to expand...

Thanks Sal,

No template needed, just the length of the table port, to starboard, and the width of the table bow to stern....thats all i need

YES..... its the table below deck...

Very Apprecative,

YOUR about 70 miles away, to bad your so far out east...zip 11939..map quest...We are `11757
 
Sal A said:
Bill tomorrow I'll try and get up in the boat I'll make a template of the table you want the one in the cabin correct


Sent from my iPhone using Tapatalk
Click to expand...

Sal,

Thanks,
F.P. only wants to sell me the whole set.....not just the switch panel...ill keep looking...thanks
Bill.
 
Hi everyone ! I have a question about spark plugs I have a 5.7 horizon I/b the plugs that are in the engines are ac delco 41-985 the parts store told me they are discontinued the new number is 41-926. The new plug is double platinum and not iridium has any used these new plugs ?
 
I want to order zincs for my 2001 310 with inboards, but don't know what sizes I need and boat is a 2 hr drive. Can someone help me out? Need prop, hull, and trim tabs. Anything else? Thanks, all.
 
Assuming everything is the same as mine, the Trim Tabs are R3 (3 3/4" diameter), the hull is 5" center to center, and the prop shafts are 1.5".
 
Next week I am going to sea trial a 2000 Sea Ray 310 with 350 engines and V drives. I really would appreciate some advise from current owners on what to do and what to watch during the sea trial to have a good indication if the boat is performing well or not such as RPM at wot, oil pressure, water temp etc. Thanks.
 
bayboatersf said:
Next week I am going to sea trial a 2000 Sea Ray 310 with 350 engines and V drives. I really would appreciate some advise from current owners on what to do and what to watch during the sea trial to have a good indication if the boat is performing well or not such as RPM at wot, oil pressure, water temp etc. Thanks.
Click to expand...

310? or 380 ? your profile says 2000 380...
 
bayboatersf said:
Next week I am going to sea trial a 2000 Sea Ray 310 with 350 engines and V drives. I really would appreciate some advise from current owners on what to do and what to watch during the sea trial to have a good indication if the boat is performing well or not such as RPM at wot, oil pressure, water temp etc. Thanks.
Click to expand...

Im assuming you're having a Surveyor Inspect it.
He will know what to look for.
Do oil samples on engines/trans/generator
 
You must log in or register to reply here.

Forum statistics

Threads
113,238
Messages
1,429,079
Members
61,119
Latest member
KenBoat
Back
Top