Search results

Found out that the EFI units have an electronic governor. Replaced the sensor, didn’t fix it. Found out that the sending unit was most likely my next option. It was very rusty and one of the terminals broke off when I touched it. When that happened the “ext alarm” light came on. I replaced the...

Is it this guy right here?

Yes, it was doing this before I replaced them.

It has 7.4 MPI’s and the port engine is running a little rough and rich at idle. I replaced the idle control exhaust sponge. I just installed a new iac on it today, all to have the same problem. When easing into the throttle throttle when out of gear, it starts jumping at the 900ish RPM range by...

Not to sound ignorant but where would I find that switch? This isn’t the one the boat came with, it’s an updated, EFI version from the late 20teens.

Anyone else ever have an issue with the oil pressure light coming on with these? Runs for about 30 seconds and shuts down. It has plenty of oil. I pulled the filler lid from the valve cover and it’s pumping plenty of oil. Not sure what the issue is. Maybe the sending unit? Any help is appreciated.

Thank you for you reply. I’m just wondering if the 18” diameter would be too big with the 99-02 340’s when I went from 17 to 18 on my old boat, the maneuverability was leaps and bounds better. I’m just not very educated when it comes to props/sizes. Most of the research I’ve done on here has the...

Quick prop question. We got our first 340 last November. It’s a 2000 with 7.4 MPI’s and the 1.5:1 transmissions. It currently has 17x16 3 blade props on it. They certainly have some cupping to the blades, but I’m not sure to what extent. They aren’t in bad shape at all. I’m pulling the boat out...

I don’t envy you. It’s a dirty job but you should be good for a long time now.

Looking now, I probably should’ve put this in the section for gas engines/transmissions.

Having a strange situation with my starboard unit. I was out 2 weeks ago and cruising at roughly 2900RPM. Trans started slipping and wouldn’t engage F or R. I let it sit for roughly 10 minutes as I limped back on the port unit. When I tried it again, it worked fine. Got back to the dock and the...

Does anyone know where to source them? The only number I can find to identify it is c013f. Sorry to be so vague in my search but I’m really lost here. I purchased the boat as a project for very cheap. Many of the items were stolen off it and this is one of them. It’s a 95 330DA and I’m pretty...

Does anyone know which cables I need for my 95 330DA? My port throttle cable is shot and I would really like to use the old one to fish the new one through. Problem is, I’m not sure which cable I need without measuring it. Thanks in advance for your help!

Forgive me if this has already been asked but how would I be able to identify which model my generator is? I’m pretty sure it’s a 4.5 kw generator but I’m not sure. It’s in a 95 sundancer 330.

That’s what I was thinking too but I was told the opposite from the local prop shop. He’s pretty reputable too, which is why I took his suggestions seriously.

I honestly don’t know what the performance was with the old ratio because I never got to drive it with them. It’s carbureted and both carbs are new. I really don’t know what else would be holding it back but it’s definitely struggling very badly.

I just put fresh bottom paint on it. At that RPM, I’m running around 13MPH, based on the GPS.

I have a 95 Sundancer that I purchased as a project. It came with the Hurth 1.56:1 tranny and they both needed replacing. I couldn’t find 2 of the same ratio that were in my budget so I had to go with two 2.0:1 transmissions. The props on the boat are 17x16. I never drove the boat before so I...

I purchased a 95 330 Sundancer last year and it didn’t come with the back or side seat platform. Does anyone know where I may be able to source one of these? I’ve searched everywhere and had no luck at all. I can make out without the little side seat but definitely need the back seat platform...

So sad! Luckily the wind blew it away from the gas dock. They weren’t able to rescue the dog.