Search results

Has anyone had to replace the windlass solenoid located in the bilge? My panel light will not go off leaving the windlass constantly in the on position. We previously replaced the windlass solenoid in the anchor hatch but this problem appears to be possibly a bad ground/fault in the bilge's...

I just received my renewal notice. WOW - they keep raising the annual premiums. I just switched from GEICO to Progressive for my auto insurance and saved almost 50%. Does anyone have any recommendations for obtaining lower-cost insurance premiums?

I have an 2006 340 Sundancer. I'm considering having the hull completely painted. Does anyone with a similar model have experience in what I should anticipate in costs? Also, if you have a good referral in Southeast Florida to do the job would be helpful.

OEM Sea Ray Electrical Switch Pad STBD Module Rv3 Searay1810626 https://ebay.us/SQMIm5 is $442.00. My vent switch will not trip open, only close. This appears to be an expensive replacement part. Any suggestions?

Does anyone have the water pump model information for replacement. My water pump will not engage after being idle for several months. I cannot locate in the Sea Ray 340 SUNDANCER 2006 Part Manual. Thanks....

Anyone has any suggestion on replacement of this interior trim that was damaged due to a water leak?

Any suggestions on painting the bilge? My boat has a fair amount of gel coat that's cracked off any makes the bilge look dirty and problematic.

I recently had my mechanic replace what I thought were all of the hose clamps in the bilge. Come to find out he missed a bunch and consequently, I've had 4 break off underway with the associated hoses falling off and cause an overheat. I'm told that stainless steel hose clamps get salt water on...

Has anyone replaced the riser exhaust hoses? My mechanic quoted me $684 for each engine hose plus labor to install. This seems to be stupid expensive.

I need some advice regards the blue fuel module plugs. One of the plugs is now missing causing water to pump into the bilge. Are replacement plugs easily available and do they just screw into the hole; presuming it's a threaded hole. If this is the case, why do these plugs pop out in the first...

My 2006 340 Sundancer OEM had 2 separate AIRMAR transducers. One was in the center of the bilge and the 2nd (Raymarine) was port side opposite the stringer from the 1st. According to SR the 2nd was a Raymarine Smart Craft speed wheel transducer part #E2601-M78712. According to the specs it...

Does anyone know what is the factory default for the keel offset on 2006 340 SD?

My windlass power light on dash will not turn off. The up/down buttons do not operate any more including the 2 on deck by the windleas/anchor. Breaker is not tripped. Any ideas why this light would be on constant and not have the windlass operational; nothing at all - like no power to the...

My 2006 SR Sundancer 340 appears to need a new A/C. The compressor tries to come on but fails and overheats shutting down. Water flow is very good. A/C technician says best to replace unit but quoted me what appears to be a stupid high price. Does anyone know the appropriate replacement unit...

I'm considering installing Sonihull on my 2006 340 SD. Obvious easy access in the bilge to place the aft transducer. Does anyone know how/where access to the forward bilge that the forward transducer can be placed? Near under the V berth A/C unit would be the best location but don't know...

Any suggestions on where to locate this door lock seal?

Here we go again: it appears my generator needs a new electric controller. When attempting to start the codes go from CC to OC without any cranking. Generator service expert diagnosed what he believes to be the very expensive electronic controller has gone bad but possible electric harness issue...

Okay, I finally did it. Being more concerned and focused on bringing up the ladder I left the anchor down. Needless to say no more anchor or rhode. I have a 2006 340 Sundancer that had according to the specs a 25lb plow anchor. However, if memory serves me correctly and comparing anchors I...

I removed the outside cabin table and pole storing the table inside the bottom of the hatch. The pole doesn't seem to fit in the clamps on the bottom of the hatch. My real issue is covering the hole. I bought a 4" deck cover but the hold it about 0.5" too small so the cover doesn't fit. Does...

Has anyone resurfaced their flooring? I have some old faux teak that needs to be replaced and it appears costs are all over the place. Suggestions ? Costs ?