Search results

Hi, I'm getting a SEA PUMP CKT HI alarm on my SmartCraft when I'm cruising. Also showing ENGINE POWER LMTD. Engine (8.1) is running fine and is not overheating. Anyone has an idea on what could be the issue? Thank you! Hugo

Hi Mark, Thank you for the info. The Marina wants to charge me 6 Hours ($85/hr) for changing both impeller…I guess it's a bit to much but doesn't look like an easy (or accessible) job to do either... Hugo

Anyone knows how long it should take to change impeller kit on both engines (Mercruiser 8.1) on a Sundancer 360 (2005)? Also, if anyone has pics or videos it would be great! Thank you, Hugo

JV, thanks for all the info...suppose to see the 2008 after labor day week-end! The 2007 I saw last week wasn't clean enough...

Thank you for the clarification. Any concern with the DTS system on long term reliability and maintenance versus the typical shifters? The 2008 I'm looking at doesn't have the zeus.. Thanks, Hugo

at 3700 rpm I cruise at 25 mph (on smartcraft) or 22 knots. Looks like I could do better if I compare to you guys!

Hi, I'm looking to buy a Sundancer 48 2007 or 2008. I would like to know the major differences between the two years. I know that the 2008 model has different throttle controllers (only one pair vs the usual 2 pairs: throttle and transmission). Is it better? Any other differences between...

Anyone knows the anchor specs for our boats, should it be 33 lbs or 44 lbs? I believe it's 33 lbs according to the measurements (14 inches x 32 inches) when I compare to other anchors on the net....I need to replace my Kodiak anchor (it's twisted!) but I'm not sure if I should order 33lbs or...

Thank you for all your feedback. Marinemax replaced my transmission and coupling for $7000 ($2500 labor + $4000 transmission + $350 haul out..) + tax. Looks like the coupling bolts loosen up and cause the problem..Make sure all bolts are tight!!!! We brought the boat back from Long Island...

Anyone knows approximately how much it cost to replace a transmission on a 360d a 2005? Thanks, Hugo

The RIB on the platform in my signature pic weighs in at about 200 lbs with motor, fuel can, and safety gear, it handles it effortlessly. Hi Mark, what kind of davits you have for your dinghy ? Would you have some pictures of it ? Thanks, Hugo

I checked the strainers but they are clean, except I found a piece of rubber (see pics) in the starboard strainer (but my H2O probleme is on the port side)...any idea of what could be this piece of rubber ? Next step I guess will be to change the sensor...

I went under the boat to see if something was blocking the water entry but I didn't see anything. I'm going back to the boat tomorrow, I will check if there's water in the strainers...Thanks

I just changed my impellers since I had an alarm last week: sea pump psi lo and the guardian was operating on the port engine. We took the boat this week end and now I get a new alarm: sea pump ckt lo (Sensor alarm / engine power limited). This time, the guardian was not in operation...

Thanks Guys! I think I found the sweet spot for my freezer temp. Also run the humidity control on the AC when we are away and it seams to solve the condensation issue. My3sons, where is located the "wine cellar" ? Under the bed? Can always use more storage space!!!! Thanks, Hugo

Hi! I just found this thread..this is great. We purshased our 360 DA (2005) four years ago already (in 2008). Boating on lake Champlain, upstate NY but we live in Canada (Montreal). Anyone of you have a condensation problem with the cabin freezer ? Mind just leak water into the drawer...

They changed the "muffler IAC" ($2/piece!!!) and so far so good! Hugo

Thanks for your feedback. The mecanics will take a look at it this week... What is a Knock Sensor for ? Expensive? Thanks, Hugo

Hi, I have a 360 Sundancer (2005) with 8.1 Horizon engines. I have a alarm on my Smartcraft over the week-end : Starboard engine power limited. Code KNK SNSR1. The alarm will go on when I run under 2000rpm only. Anyone knows where I can find the code meaning ? Thanks, Hugo

I'm looking to have my canvas replaced on my 360 Dancer. My boat is located in Plattsburgh (NY). Anybody to recommend in the area or Burlington (VT) ? Thanks!