So officially, at the longest / tallest spot on the mattress, it is 72". At its widest, it is 60". I hope that helps.
Sent from my SAMSUNG-SGH-I337 using Tapatalk
Bennett - We are going to the boat in about an hour. I will measure for you. I myself am 5-10 and I am comfortable on the bed. Thanks, Bobby
Sent from my iPad using Tapatalk
Thanks for the link. Some one told me the the air lock symptom could be due to a blockage in the vent. I see this has a breather valve on it, perhaps that's the part he was referring to. That may be a good place to start to see if it's in good shape.
I am wondering if anyone has experienced an "air lock" or pressure in your ZF transmission. My issue is that when I engage the transmission, I get a loud squeal or the sound of metal on metal. It does not happen often. I have plenty of transmission fluid and brand new cutlass bearings. When...
I'm needing some advice / help. I have a 2007 320 sundancer, mercruiser 350's with drives. Both of my motors have dropped to an idle RPM of 400 - 480. I believe this is causing my stalling out issues. I replaced the IAC's on both motors but that hasn't solved my low idle issues. By the...
We are going this year and I am counting down the days till we leave. Has anyone taken any classes on the water? I signed up for advanced docking, a 3 hour class. It wasn't too pricey and I figured it would be a nice boat ride if nothing else.
I am hoping for some help / guidance here. I have a kohler 5ECD generator on my 2007 320. Two weeks ago, it started shutting down and gave me a CO 3 code. I have replaced the PCB Board as well as the CO sensor. The generator ran for 5 hours then shut down again with CO 3 code. From what I...
skunkman, Welcome aboard! I am new to the cruiser world, almost 2 months with my 2007 320. This site is the best all around sounding board you could have. Great advice and most will help you trouble shoot issues should you have any. With a new boat that shouldn't happen.... well it's a...
Spikedaddy99, im not sure of the impellers for 5.7 Mags. I run 6.2's. Maybe the following link will help. You click Launch Parts catalog, and enter your serial number. I got the link from mercruiser customer assistance. Http://www.mercurymarine.com/parts-and-accessories/parts-catalog/ I...
I apologize for jumping in but I have this same issue. Windlas was great until Monday. Now, when you step on the foot control, it clicks and all the sights go dim and the radio quits playing. I haven't checked the fuse in the anchor locker. I will do that tomorrow.
This weekend, the belt on my starboard engine split in half. It looks like someone cut it. I have an extra belt and was about to put it on but I began to wonder why it split. It is a new belt, 2 months old. I tried to determine if one of the pulleys was stuck or froze up causing it to break...
So yesterday the wind were high and my generator shut down. I got a code like yours, well almost, CO2. The best I can tell is the waves were sometimes filling up my exhaust port. I turned on the blowers and changed position of the boat. Once I reset, shes been running good. I don't know if...
So it turns out the seal on the sea water pump was leaking, causing the bearings to heat up and expand. Once it heats up and expands, the impeller side seizes up and quits spinning. Once the impeller quits, the gear drive keeps on spinning causing the drive sleeve to be chewed up. Today I...
OK, 2 drive sleeves and impellers later, no generator. The Genny will spit water for 10 minutes then nothing. I take it apart, the drive sleeve on the seawater pump side is chewed / eaten away. I know I'm coupled to the gear drive on the motor side when it starts. Has anyone dealt with this...
Thanks skolbe. I'll give that anchor a look. Makes sense that it's coated so it can be stored easy. Thanks for the input
Sent from my SAMSUNG-SGH-I337 using Tapatalk
I am looking for a secondary anchor for the back of the boat to hold me steady in our winds. I am curious as to if anyone here uses one and if so, what do you use. What is the best kind? Most of our bottoms here are muddy not sandy. I would appreciate any feedback you may have.
The original drive sleeve was in the bottom of casing. It was split in half. I know I had to do something wrong. I think I will make sure the pump housing isflat on the plate, put the drive sleeve on the pump housing then push it onto the gear that is on the motor side. Maybe I will get a...