Search results

Today I had my first encounter with hitting something with the props. I was at ilde and hit a piling. The engine stalled. I immediately raised the drive and found only a small "ding" in one of the props. Started the boat, shifted into foward and reverse with no problem. Everything seems...

Hope everyone had a great weekend on the boat. I have been working on my boat name and am planning on ordering it this week. I want to match the color and font from the lettering on the back of my 230 select. Can anyone give me the font that SR uses? Thanks in advance, See the pic below...

Anyone have any experience with a trim pump sticking in the on (driving the outdrive down) position. I am thinking it was the trim switch on the throttle sticking. After shutting down the motor at idle when I heard the pump running, I turned the batteries off to protect the motor from...

Yesterday it took several attempts to start my boat, starter engaged and boat immediately started then stalled approximately 5 times. It ran fine above 1500 RPM's. At idle it surged, stalled, and shut down. A local mechanic was available, he connected the computer to the motor and found no...

Yesterday it took several attempts to start my boat, starter engaged and boat immediately started then stalled approximately 5 times. It ran fine above 1500 RPM's. At idle it surged, stalled, and shut down. A local mechanic was available, he connected the computer to the motor and found no...

I have a 230 select with the dark blue on the sides. We raft up with others on weekends, and as a result, the sides are covered in very shallow scratches in a vertical pattern in the areas of the bumpers. I have tried canvas covers, the large vinyl bumpers, my bumpers, other peoples bumpers...

I am going to install a flush mount combination grill / table mount in the corner of the swim platform opposite side of the swim ladder. The platform is approximately 9 inches thick and has no access from below. I am assuming its hollow but dont want to pic a location and start drilling until...

Anyone have pics of a 230 (or 210) select boat name. Locations look pretty limited, either on the end of the swim platform or on the stern just above platfrom. ??? Our boat name is "Summer School". Hoping to see what others have done on runabouts.

It may have been discussed, I searched 1st, but did find the answer. 2nd year on my 230 and the canvas is covered in pollen stains. I need to clean it?? Opinions? Can it go in a laundry mat? if not how can I clean it. Thanks in advance. Mike

javascript:gotoSlideShow('http://www2.snapfish.com/slideshow/AlbumID=275589223/PictureID=6980654967/a=39795233_39795233/') Did it work

I have almost finished adding a second amplifier and wakeboard tower speakers to my 230 select. I need to drill holes from the inside rail to the outside of the rail near the wakeboard tower in order to run the wires. Similar to how the anchor light is run. So several questions, 1. how do...

1st day of spring on the Potomac. 85 and sunny, the crew is in tip top shape.

OK, I'm sure this is a simple question, but since my boat is still locked in the boatel I cant go look for myself? How can I run wires from the dash on the drivers side to the dash on the passenger side? I am installing a remote for the stereo and am not sure of the pathway? Do wires run down...

Merry Christmas, Yes a couple of early Christmas gift arrived today. I picked up a set of infinity M6000 tower speakers to add to my 230 select. I have the stock clarion cmda4a head unit with a 4 channel amp and the polk audio 6 speaker set up. I am adding tower speaker to allow the music...

Hey, I'm sitting at home thinking about installing some type of tower speakers on my tower. I have a 230 select with the Fision Tower. I don't know the diameter of the tower and the boat is 30 miles away. Anyone know the diameter of the tower? Anyone put speakers on the Fision tower? Or...

Good Day, I have a 230 select with a 350 mag BIII. It has the perfect pass system and the external paddlewheel for the speedo. The paddle is damaged from a crab pot encounter. How do I find the part necessary to repair/replace. Is this a merc part or perfect pass? any sources? Does the...