Search results

Out of a 1989 Sundancer 300. New block in Jan 2014. Approx 50 hours on engine. Located in Ruskin Fl at Little Harbor Marina. Removed from boat in January. $2400 (314) 484-6727

Have removed both motors from my Sundancer 300. I want to put it back in the water for now. What is the best thing to use for ballast? Any negative / positive thoughts on bags of playground sand from Home Depot?

I have a 5.7L 260 hp Mercruiser with aprox 25 hours. Replaced engine and manifolds in Dec 2014. Fully dressed and ready to put in your boat. I also have 2 full, front and back, Gimbal assemblies with trim tabs, lines, trim motors, and "Y" pipes. (They are not pretty because they have white...

Anyone know how much a Quicksilver 4 KW generator weights?

How do you safely remove the fire bottle from engine compartment?

I need to pull an engine from my 1989 Sundancer 300. When I pull the drive does the throttle need to be in any particular position? Are there any gotchas on the disconnecting of components from the engine, or any techniques that would be good to know? Thanks

I have a 1989 Sundancer 300. I am taking the engines out and I want to put it back in the water with just the stern drives on. What else do I have to do to make it float worthy? I have also heard I can buy plates to put on the inside to keep all water out. Thanks

1989 Sundancer 300. How does salt water affect the A/C and Gen? What techniques work well to keep system flushed.

I have a 1989 Sundancer 300 that I am going to move from a fresh water wet slip in Sanford Fl to the Tampa Bay Area. I have IOs / raw water cooling so I don't want to leave it in a salt water slip. I have heard that it is not good to take a boat this big in and out of the water with a fork lift...

89 Sundancer 300 / I changed my shore water hose and now I have weak water pressure in galley but strong pressure in lav. Switched back to old hose and pressure still low in galley. Any suggestions? thanks

When I run the Air Conditioner for long periods the carpet just under the stairs and in the aft berth are wet. Looked all around the unit and can not find obvious leek. Area around the floor in the aft berth and sump area are dry. Suggestions?

"89" Sundancer 300, 5.7 Mercruisers w/carburetors, Alpha I Gen II drives. After engines have been running for a while, and coming back to dock, port engine stalls when shifting from neutral to either fwd or rev. Chokes are not connected and engine has a slight low end knock. Port engine doesn't...

I have a Norcold Tek II DE251 in my 89 Sundancer 300 that has stopped working. They don't make that model anymore. Is there a replacement model #?

Anyone have a site to go to to find new throttle control body for a 1989 Sundancer 300

1989 Sundancer 300: I need a seacock for the generator. The lever on the old one snapped off. Can someone give me a good web site to go to?

Anyone know how much carpet it would take to re-carpet the inside of a 1989 Sundancer 300? Any suggestions on a good type or brand?

1989 Sundancer 300...... I need a new battery charger. I have three batteries. Any recommendations?

1989 Sundancer 300. I am hooked up to shore power and had all my cabin lights on for about an hour or more. My carbon monoxide detector started beeping and alternation Red/Green. I noticed the cabin lights seemed dimmer than usual. I checked my battery charger and it was reading 0 amps. I turned...

89 Sundancer 300, how do you take the dinette backs off to reupholster? Mine has buttons across the middle.

Mercruiser 5.7 (carburetor) after engine has been run for a while and while docking engine stalls when shifting into reverse.