Search results

Hi . My port4 in 1 gauge died. I need to replace it p/n 1040905 . No seems to have it. All that I find are smart craft , is there a way to connect the smart craft to the nine smart craft gauge????

hi , my gimbal on port engine is leaking. its an alpha1 gen 2 . how do I know were is beat to order and if its a gen 2 does the year matter???? would greatly appreciate your help. thanks mike

Hi my 02 sundancer has a kolher 5k model 5e generator. Lately when I shut it off after a few hours of use. It will turn on by itself??? Even if I shut of the gene and shoreline switch.. Has anyone had this issue????

Hi, my trim connector block went bad, my question is when I removed the cover. Instead of a zinc plate it has a plastic cover with a sensor on it. 2 wires run thru the hose connector into the gimbal. Can I cut the wires and eliminate that sensor? And or what is that sensor for?:huh:

H, I need to replace my sunshades on my 280 . Does any one know where to get the best price and the right fit ? thanks

Does anyone know the correct part number for the iac motr on 2002 mercruiser 4.3 efi w/tbi. Tried 3 all are different. please advise thanks

hi. need help with smartcraft gauges. this is on a 2006 300 sundancer.I cant get the depth finder to work on my gauges. it use to show on the starboard gauge. I reset the three gauges and it doesn't work any more , it shows them trim but not the depth finder. when I reset the gauges . I set the...

hi. need help with my smart craft gauges.I use to be able to see my depth on the starboard gauge display.nd know it doesn't work. I pressed the reset on all three gauges and it disappeared. when they reset. it asked . which engine port or starboard I set the starboard first. it asked for...

Good morning . Does anyone know if there is a breaker or fuse for the water pump for the a/c unit. I turned the a/c on and there is no water coming out of the pee hole. I don't see anything but the main breaker for the unit?

Can anyone help me on what is the best way to tackle replacing the waste holding tank?

i have a leak in my holding tank, i repalced the hoses thinking that they were seeping thru. the only thing left is the nasty tank. is their a repair kit or does it have to be replaced? what is the best way to deal with this thing?

Need help. I had my boat in dry dock for about a month. Recently had truck and trailer stolen and was forced to get her in to dry dock. I noticed that the wood were the seacock for the a/c pickup tube , has the fiberglass that covers it cracking around it. Should this be a concern? Should I pour...

Hi again second problem, I noticed water rising in the bilge when I turn on the fresh water pump . I followed it and it was coming down from behind the water heater. I shut the water pump off dried it up and rode for about an hour. After checking the bilge it was dry. We over nighted and in the...

Hello to all, I recently notice an odor that smells like ammonia when the boat sits for a couple of days. I was wondering if anyone has encountered this? Could it be the filter on the holding tank clogged?

i need to replace the fuse box. its called interface fuse module. does anyone no where i can get it?

This is a 2002 searay 260. 5.7 efi bravo drive. I replaced the coolant sensor and checked the spark at the plugs. Engine won't start unless I throttle up. When starts it lets out black smoke and runs rough for a few seconds. After that I can leave it at idle and it idles fine. If I shut it off...

water leak thru port light window. does anyone know where i can order the rubber molding that seals the glass. please advise. thanks mike

i have a someplay on my port engine (not up and down, but side to side) i check end there is a rode that goes from the starboard engine to the port engine. the connection to the port has a tie rod that has play. has anyone replaced this? can anyone one direct me on where to get this part and...

On my port engine the rod that connects the starboard to the port engine steering lever has a tie rod at the port connection. Has anyone ever replaced this tie rod and do you know who carries it? Much thanks

my motor went bad, i havent been able to find a replacement motor, the motor i have is a 400watt 4 cable connector. the only one i find is a 500 watt motor and it only has 3 cable connections. does anyone know if i can use the 3 wire ? and if so what do i do with the extra cable