Search results

Yes I used meguires medium cut with a milwaukee hi speed polisher and an assortment of pads. I will post pics of the redone cabin once I open it up in the spring. ***I also hand buffed after power buffing!

i forgot -I also installed an xm radio with marine antenna, the antenna is on opposite side of vhf antenna and has a 2 foot chrome extension.

What I have done already -all new cabin interior upolstery and cushions -redid every cabinet door myself -BUFFED BUFFED BUFFED Removed baked on decals (very long process) redid the 2 inch in olympic blue and added the SEA RAY decals where it used to say WEEKENDER, BUFfED BUFFED BUFFED -added...

Actually she sat uncovered in a driveway for years. I bought a milwaukee high speed polisher and also did alot of hand buffing.

more pics to come, what do you think?

My current set up is like this- 1 battery on starboard side-It's #1 on the switch and starts starboard engine and runs house loads. I only use the swith in the #1 setting. 2 batteries on port side-One of them just starts the port engine. It is isolated from the rest of the system, not on...

done deal cut main #8 off of battery feed hot behind panel,properly crimped, heat shrunk and bolted a #10 fused at 25A to the aux panel. Ran DC- to main # 8 tied in at one of the guage posts suggested in manual. Now to run the 3 circuits. Anybody have any qualms about leaving a #12 fused at 10A...

I recently took all the stripes off my 260 weekender. Took a long time but 3m sells a product just for this. It looks like a big eraser that attaches to a drill then you just rub it off. This weekend I'm gonna finish buffing above the rub rail then apply my new 2 inch vinyl. It is all a...

Named by previous owner but I like it. HEDONISM Means the pursuit of pleasure.

No panel on the underside of deck, no breaker /fuse box anywhere. The switched leg off my 1,2,or off battery switch goes to engine/alternator and a wire harness that powers house loads and starboad instruments on panel. I did find the main #8 hot and ground that feed everthing behind the...

the 20 amp circuit is #12 wire-good for 20 amps. But it just runs to # 1 battery-not good. I'll look for this panel this weekend and If I don't find it I think I'll run a #8 with 30A fuse right to baterry switch output. Does this sound like it will work?

I have a 1,2 both or off battery switch. Is there a panel of some sort in engine compartment that the switched leg runs into?

Does anyone have any idea where the main power junction is. I've got twins on my 260(see signature) so I have 3 batteries. One is dedicated port start only. The other 2 are on selector switch. When I bought the boat the cd radio was connected directly to my #1 battery( 20 amp fuse at battery of...

my boat has a blue coating of bottom paint. I think its an albalative as it will stain my hands blue if I rub it. It needs to be repainted. Is there a product that can go right over the old with minimal sanding?( just the peeling parts is all I would like to sand)

So my boat has a blue coating of bottom paint. I think its an albalative as it will stain my hands blue if I rub it. It needs to be repainted. Is there a product that can go right over the old with minimal sanding?( just the peeling parts is all I would like to sand)

So I,ve had a 1985 260 weekender for about a year now. Have done alot of work to cabin, the twin 190/3.7L mercs and decals and buffing. I love the boat. I have 2 manuals from mercruiser that say MR drives. Does this sound familiar to anyone?

job completed in 5 minutes this weekend. you might need to cut through the old putty with a knife to help you pull it out. I didnt use caulk as the putty provided on the bellows worked great. just make sure the valve assembly on the new inlet tube is on the bottom when you install it.

Mine is just an Aquamate also-no model #. Look at the directions sticker under the lid for the serial #. Thetfords phone # is 1-800-521-3032. Your toilet is probably same model as mine. Bellows replacement part #-07862 inlet tube with valve part #-07024

i'm putting it in this weekend i'll let you know how it goes. go to the thetford website and get the customer service #.Get the serial # off the toilet and you can buy the replacements directly from them. If your toilet just says "aquamate" like mine does its probably the same part. It was $23...

I just received my replacement bellows from thetford ( www.thetford.com ) for my 85 260 Weekender. The directions state to cut thebellows in half then pull out with pliers. you then have to take the flush tube off of the old bellows. I also ordered the inlet tube which needs to be replaced with...