Source for stainless steel engine vents

[Ka1oxd]

Jason, I will take a picture with a ruler along side this weekend. The blueprint in this thread is too small for me.

 

[Pyrojodge]

Jason, I will take a picture with a ruler along side this weekend. The blueprint in this thread is too small for me.

Thanks James... did you see my reply about the ladder?

 

[Nehalennia]

Thanks Doc. I'm sure everyone is happier at this price.
James if you have different dimensions, let me know ASAP and maybe I can work them in.

 

[Ka1oxd]

I will not be down to the boat until Sat, I will get back to you that night.

Jason, no I did not see the post on the ladder. will look now

 

[skillz48047]

im in for 6 like i said, but i have a little bit of concern.....i cant get to my boat until saturday to measure but when i replaced mine last year i bought them from searayman13 off of ebay as im sure alot of us have, i went to one of his listings to get some dimensions and im pretty sure the ones that fit my boat are 14.125 long but they are 5.625 tall, not 4.625........ like i said ill double check saturday, but even the rendering of the vent looks a little short, seems to me that the screw holes are a little too close to the outside edge, not sure if anyone else sees it this way.......

 

[Nehalennia]

Ok Skillz just update me if they are different. Please let me know by Monday.
Is everyone OK with PayPal?
Everyone ordering please PM me with your email address and phone.

Thanks again guys.

 

[Pyrojodge]

Todd, Let me Wait and see what James comes up with as I am sure that mine are exactly like his. The vents I purchased at WM were not even close to fitting the hole. The WM ones measure 13.25"L by 4.75"W by 1.70"H and were no good....

Let me wait for James measurments and I'm all in...

Pay pal is fine for me...

 

[Nehalennia]

Ok. Make sure the inside sleeve that fits in the hole is measured too and the screw pattern is noted. Check out my drawing and adjust yours accordingly.
Thanks.

 

[Pyrojodge]

Todd, After a little research this it what the 340 owners have... the measurements are as follows...

14" by 5.625 by 1'' Have no idea on the hole pattern sorry Todd...

 

[skillz48047]

without having mine in front of me, im almost positive thats what my boat has as well.......
like i said i will take a picture and measure mine tomorrow and have it posted tomorrow afternoon
paypal is good with me, i will PM you as soon as i get these dimesions for you so we can make sure were all on the same page..

 

[Paladin]

Does anyone else have concerns about rain water coming in? Rainwater does indeed come through mine, ( I don't have a DA tho) and I have been looking for the vents that have a "hood" over them, like I've seen on the older Tolly's. For both sides and transom. Haven't had any luck. I even looked at car window rain shield type things...

 

[Pyrojodge]

Does anyone else have concerns about rain water coming in? Rainwater does indeed come through mine, ( I don't have a DA tho) and I have been looking for the vents that have a "hood" over them, like I've seen on the older Tolly's. For both sides and transom. Haven't had any luck. I even looked at car window rain shield type things...

I know its not possible in mine as my blowers draw from the top of the box... my vent boxes are also sealed so I don't see it leaking down the sides of the box either... I did happen to think about birds making nests again in my collector box...

 

[Ka1oxd]

I will have the pictures and the measurements up by 8 pm tomorrow.

 

[Nehalennia]

Yeah I have thought about it too and don't think I will be any more or less than the origInal stock ones.

 

[skillz48047]

Here are the pictures of a vent off of my boat, dont mind the peeling chrome, i sent them out last year to have them "sprectra chromed" obviously the process is a POS cause they didnt make it 3 months!!!! anyways......

the measurements are 14 and a light 1/16th long by 5 and 5/8 tall
the holes are all about 3/4' from the edge of the vent to the center of the hole on the long sides
and 3/4' from the short side to the center as well
then they go roughly 3/4" 4 1/8" 8 5/16" 12 1/2" that is the centers of the holes

i can send it to you if you feel you need it

let me know if there is any other information you want or need

i cant upload the picture it says its too big of a file
i dont have the patience to mess around with that
if you want the pics give me your email address and ill send them that way this website is really making me mad right now

 

[Pyrojodge]

Here are the pictures of a vent off of my boat, dont mind the peeling chrome, i sent them out last year to have them "sprectra chromed" obviously the process is a POS cause they didnt make it 3 months!!!! anyways......

the measurements are 14 and a light 1/16th long by 5 and 5/8 tall
the holes are all about 3/4' from the edge of the vent to the center of the hole on the long sides
and 3/4' from the short side to the center as well
then they go roughly 3/4" 4 1/8" 8 5/16" 12 1/2" that is the centers of the holes

i can send it to you if you feel you need it

let me know if there is any other information you want or need

i cant upload the picture it says its too big of a file
i dont have the patience to mess around with that
if you want the pics give me your email address and ill send them that way this website is really making me mad right now

Here are the pictures...

 

[Ka1oxd]

I just got home and here are the pictures. 5 5/8 x 14 1/8

 

[Ka1oxd]

I guess Jason you had to go hug your boat today to get the pictures?

 

[Pyrojodge]

I guess Jason you had to go hug your boat today to get the pictures?

Nope, sorry to say, I posted them for Skillz

 

[Nehalennia]

James
Were you able to get the screw hole placement dimensions?
Also were you able to get the dimensions of the flange inside that skirts the cut out?