nibral props for sale 17"x 20" 3 blade 1.1/2" shaft

[white glove boat]

two sets L&R reconditioned and cupped 17"x 20" 3 blade nibral medium cup for sale $500.00

 

[bobeast]

I'll take a set. Price shipped to 95023?

 

[white glove boat]

that zip is zone 7 Fed Ex from me and I'm guessing weight at 35 #? that says about $30.00 in ground freight . In any case it can't be much more than that even if I missed the weight.I could get an exact figure and get back to you ? `you only want the one pair?

 

[bobeast]

that zip is zone 7 Fed Ex from me and I'm guessing weight at 35 #? that says about $30.00 in ground freight . In any case it can't be much more than that even if I missed the weight.I could get an exact figure and get back to you ? `you only want the one pair?

Yep 1 pair would do it for me. Please PM me with the exact total and your PayPal address, And I'll make you rich....well. maybe not rich....

 

[Motoguy2158]

two sets L&R reconditioned and cupped 17"x 20" 3 blade nibral medium cup for sale $500.00View attachment 61136

That was $500 for both sets? I see one set is gone...I'd be interested in the other set.... zip 48040

 

[white glove boat]

ok I can get a shipping cost and get back to you . Yes I sold the other identical set

 

[white glove boat]

motoguy , what is your WOT on your 6.2's ? are you in Huron or St.Clair ? the reason I ask is the 6.2 has a wide range of WOT (4800 to 5200)and the drive /engine package you have specifies a 17"x19" wheel ,I think in your region up there the extra inch of pitch will be fine. When I operated on Lake Michigan , I did run my 17"x20" wheels and reached recommended WOT but here in texas with ethanol and this flaming heat they aren't flat enough so I am now at 18"x19" .I am not too concerned I just want to make you aware . They will probably be perfect .I am sure you know this but I want to make sure.

 

[white glove boat]

about $100.00 for packing and freight

 

[M Prod]

Wow ths is a DEAL. I wish they fit my boat!

 

[white glove boat]

yes it's an extraordinary deal since a set retails for about 1400.00 , I have been sitting on them for a while and the solution is not correct for me here in Texas . I thought I could help some of my fellow boaters out seeing how EVERYTHING we buy for these toys is a hose job!

 

[bobeast]

Wow ths is a DEAL. I wish they fit my boat!

ikr? I had an order in with General Propeller Company. They quoted me $800 for a single wheel with a 5 week lead time from Michigan Wheels. Say not needed, I canceled that order and jumped on these. Thanks @whitegloveboat for an awesome deal.

 

[Motoguy2158]

motoguy , what is your WOT on your 6.2's ? are you in Huron or St.Clair ? the reason I ask is the 6.2 has a wide range of WOT (4800 to 5200)and the drive /engine package you have specifies a 17"x19" wheel ,I think in your region up there the extra inch of pitch will be fine. When I operated on Lake Michigan , I did run my 17"x20" wheels and reached recommended WOT but here in texas with ethanol and this flaming heat they aren't flat enough so I am now at 18"x19" .I am not too concerned I just want to make you aware . They will probably be perfect .I am sure you know this but I want to make sure.

My props are like new currently and they are in fact 17 x 19. I plan on doing some extended cruising of the great lakes and would like a set of spare props. These will get me home and to your point work fine... I just got the boat a month ago and with the bottom pretty dirty from setting around for a couple months it hit 4900 rpm... I could always get them re-pitched back to 19 if needed. The boat has been hauled out for the year so I plan to freshen up the bottom, Have my props checked and then next summer figure out whats the best. Lots of different opinions here. For now these are a great set of spare props in case I decide to chew up a log. The tabs on the 34 are ridiculously small so you tend to run faster than than you want. I have the extensions all drawn up and ready to build once I do a couple measurements with the boat out. I think the boat will then cruise down around 3200 RPM vs 3400 to 3600. Maybe lower with the 17 x 20 as long as it doesn't load up the motor. 1" of pitch is typically 200 to 300 RPMs. Thanks for the heads up...

 

[Motoguy2158]

about $100.00 for packing and freight

I can do this with PayPal....
my email: kjwood@comcast.net if you want to send me your email there I can get his done.

 

[white glove boat]

Ok I sent you an email

 

[Motoguy2158]

Ok I sent you an email

You are all set...thanks

 

[Motoguy2158]

White glove Boat, thanks for the deal on the props...It will give me a piece of mind as we venture around the Great Lakes..

 

[white glove boat]

No sweat , glad to help out. I hope to get out of this belly deep slough and get back up to South Haven in the near future. And when I get there ,the first thing I'm going to do is pass the S. Haven light , push to 20 kts and disappear west about 15 miles or so and just take it all in! Can't wait. Good luck to you and safe travels!

 

[Motoguy2158]

Got my Props today....Very nice and shiny!!! They look great...Trying to think of a way to display them on the boat... Maybe a prop rack on the transom...lol
Thanks for the great buy! Here's to warmer weather and another Michigan summer!

 

[white glove boat]

you're welcome ,be safe and I hope you'll never need them but spares can really save the day!

 

[John Leyden]

My props are like new currently and they are in fact 17 x 19. I plan on doing some extended cruising of the great lakes and would like a set of spare props. These will get me home and to your point work fine... I just got the boat a month ago and with the bottom pretty dirty from setting around for a couple months it hit 4900 rpm... I could always get them re-pitched back to 19 if needed. The boat has been hauled out for the year so I plan to freshen up the bottom, Have my props checked and then next summer figure out whats the best. Lots of different opinions here. For now these are a great set of spare props in case I decide to chew up a log. The tabs on the 34 are ridiculously small so you tend to run faster than than you want. I have the extensions all drawn up and ready to build once I do a couple measurements with the boat out. I think the boat will then cruise down around 3200 RPM vs 3400 to 3600. Maybe lower with the 17 x 20 as long as it doesn't load up the motor. 1" of pitch is typically 200 to 300 RPMs. Thanks for the heads up...

5/17/19

Have a Brand New SET of TyTorq 18"x22"x1"1"1.5" Shaft, Light Cup Was for a 370SDA--- $650 Set + Shipping ---- Leydenjon@Yahoo.com