Search results

I had a small amount of oil come out the weep hole on my A1 Gen2. I split the case and replaced the carrier seal and shift shaft housing assembly. This involved removing the water pump housing. I also did the water tube as it had a hole in it. I did not replace the water pump seals nor impeller...

It's an electric head. I think a vacu-flush but not sure. Stock 96 Sea-Ray 290 sundancer. Electric motor on the backside base of the toilet and a push button switch to flush on the sink wall. Last time out it would suck everything down fine and quick but would fill no water back in...none. Not...

Who has ordered from them and when did you pay and finally receive the platform? I ask because I ordered a swimdeck from them last week and was told they where 4 weeks out...well, they call today and left a message that it is ready. They want payment and a shipment address. That's cool and all...

How bad a job is this? Twin 4.3's in a 96 290 sundancer. The starboard engine trim grey hose needs to be replaced. The old one is out already. The heads and exhaust are off the engine. is this possible with the engine in the boat?

1996 290 Sundancer w/ 4.3LX gen+. what HP are these? I'm assuming they are the 4bbl carb'd models?

:smt038 Put a remote start on the Honda. It'll be nice to not climb up front to turn it on and off....and it actually works...electric choke and all.

I've lost the ground for my arch lights. I've run a ground up to the inspection panel and used the stock power wire and they work. The switch is good. The switch only has power out to the lights. The ground/negative is a common somewhere. I've been under the dash till all the wires go into the...

I have a 10hr lower unit for $2500. It's just the lower leg but it's like new. tgriffin36@cfl.rr.com

Brand new unused take-offs.My mistake THESE ARE BOTH REAR RIGHT HAND PROPS They are 20p and perfect.Little dusty..lol. $500obo. I can ship.

Lets Talk Canvas/Upholstery..especially 290da owners Naturally, the mid 90's models.I'd like to see how yours is set-up.I'm having mine done this week and changing some stuff. Mine is OEM great lakes stuff: Do not like: 1..My front canvas goes down to the windshield from the arch.Horrible...

I've got a problem.I bought a B3 drive from a guy and he went to jail.It's an ebay/paypal deal so good luck getting my money back without him.I can prove all this so everything is on the up and up. It is a bravo 3 lower and the props are on the shaft. I need someone to go pick this up and box...

It's a 30 hr lower leg.It's corrosion free 100%.The only poor thing is it does have a couple divits out fo the lower portion of the skeg.It does not affect it in anyway.It could also be filled in VERY easily. The carrier bearing looks new. $1500 shipped. It will be repainted epoxy black if you...

OK, this is the 1st time I have noticed this.I got a spare filter today and it's a seachoice 20911.It is for a 94 merc 7.4. I'm looking at this filter and it has 2 ring gaskets...Umm, I'm fairly certain the one I have on the boat(napa 3225 I think) does not have this.It looks like a typical...

These are the previous semi-polished version.They are spotless clean and only have a few hours on them. $550. tgriffin36@cfl.rr.com

Excellent shape and the older semi-polished style not the newer rough finish. $650

I have a set of unused new Bravo Three props.They were new boat take offs. $550 for both obo. tgriffin36@cfl.rr.com

I think I'm gonna tackle this.I need to order a rebuild kit but it's kinda hard when the boat is in storage. Can I just get a rebuild kit from an auto parts store or do I need to order one online? My engine is a early 90's 330hp 454.It's not the original engine in the boat.

So we have all done manifolds and the biggest issue is the weight of the suckers when putting them back on.You have to hold up 40lbs with one hand and line up the gaskets and not cross thread the bolt....not to mention lets not drop it on the plugs! Well everyone once in a while you come across...

Anyone have pics of it installed in a 94-97 vinatge 290 Sundancer? I'm on the fence about doing it.I loved it in my little 26' cruiser.

This is for single 7.4 Bravo 3 owners. I need to know what ratio your drive is and what props you run? I know it's 2.0 or 2.2....just not sure what came stock. Thx