I have a rebuilt aft EIM that has a 18 month service warranty on it. Global Electronics rebuilt it and i sold my 280 and don't need it. Let me know if anyone is interested. Email me at gsmallwood@charter.net
Sold my 2003 280 Sundancer. I have a new forward EIM that I purchased and never used. I also have a working used switch pad that I swapped out. $550.00 for the EIM and $200.00 for the switch pad. Email gamallwood@charter.net if interested.
2003 Sea Ray 280 Sundancer, fresh water only, twin 4.3 engines with 671 hours, generator, bilge heater, hot water heater, bottom paint, cock pit cover, camper enclosure, bow pads, magna grill, heat/AC, microwave, refrigerator, electric stove top, vacu-flush head, satellite TV with flat screen...
I have a 2003 280DA. The microwave stopped heating. It would run but not heat. I took it out and found out that it has 2 fuses. One on the top that powers the control and motor and one at the bottom in a sealed plastic fuse holder that hooks to the capacitor that runs the heating unit. Since no...
I have the original Clarion XMD1. I want to upgrade the head unit to a Bluetooth but still be able to use the helm remote. What kind of head unit will let me do this and be compatible with the remote?
I have a 2003 280 Sundancer with a 5000k Kohler gen. This weekend it was cold out and we were out at the boat parade. I had the heat on in the cabin plus we were running the microwave along with Christmas lights. It tripped the power breaker on the gen. Later I had the cabin heat on and was...
Going to be a great boating weekend for this late in October. Heading out to spend the weekend. Happy Halloween everyone.
Be safe. ( loving this weather but we sure do need some rain )
My charger/inverter fan runs but neither light is on and the meter is showing nothing. Has to have power to it for fan to run. Is there a fuse for the charging part or has it expired on me? It is an Intel Power PD 2030.
I have no functions at either switch pads. When turning batteries on both light up for a second then go out. I was told to change the forward EIM. I did and still nothing. I have an extra switch pad and changed them also with no luck. Could it be the EIM in the bilge? Just changing parts one at...
My 2003 280 was doing fine as we were anchored out. When we got ready to leave I raised anchor from helm. It worked fine. Had lights on, water on, blower on. We started home and switches were light up but would not work. Then all the lights in the switches went off but everything was still on...
I have a 2003 280SD with a 5E Kohler Gen. The boat stays in the water. I try to crank the gen and motors at least once a month during the winter. Yesterday i was going to run everything. My engines cranked fine, but the gen just turns over. It does not even seem to hit. It is like a switch is...
Do you splice your own rope to the chain if the rope has to be replaced. Mine is beginning to fray and wanted to cut off and start over with a new splice. I have no clue how to do this.
Went to the boat tonight, turned on blower and when I went to turn it off it would not. It acts like its trying but when you release button it comes back on. It's like the switch is stuck in on position. Can you replace just blower switch at the helm?
One of my windless footswitch covers broke this weekend. It is for a 2003 280 SD. It is an Imtra product. Where is the best place to buy replacement covers?
The IAC valve stopped working yesterday and the port engine would not idle. Got the alarm beeps also. Can you get the IAC at the local parts store? Alot closer and cheaper than the marine store.
My heat/ac thermostat is acting up. Sometimes it works perfect and sometimes it won't do anything even though the display is on and it says either heat or cool. When acting up it won't let you change the settings or even cut it off. When working the unit works fine. Could the thermostat just be bad?
I had the boat pulled and bottom paint touched up. When we put it back in and run it on plane the the genny will not prime up. Changed impeller and it still will not pump. Cleaned strainer, there is water in the strainer but does not overflow with the seacock open. Any suggestions?