Search results

I have twin 2015 Merc 8.1 horizons in my 97 Searay 330 EC. When i run at higher RPMs over 25k the port engine throws up a code in Smart craft. 1052-6 Crankshaft or camshaft trigger the device , calculation or process detected a fault. fault The engine runs fine and if I lower the RPMs back...

I need to replace the rear steering cylinder on my 97 330 EC. It currently has a SeaStar BA125-7ATM. The helm is new. I'm thinking that if I need to replace the cylinder perhaps I can replace it with an upgraded cylinder to get easier steering. Does any know what cylinder i can put in as a...

I went thru all this when I purchased the boat and the broker said the PO wants no contact. He purchased the boat and does not really know anything about it.

Why am I getting flashbacks from a Mission Impossible movie and defusing a bomb. I'm gonna need to check my life insurance and boat insurance policy first !!!

I completely agree. That's why I pulled the dash panels off. The NMEA 2k network looks a mess too. I have no idea where a keyfob would be and i can't talk to the previous owner. Just figure it out and clean it up. I greatly appreciate all the help !!

I figured this post would get some action. I was hoping it was not a self destruct timer that is set for 2 months after i bought the boat. The boat was repowered in 2012 with 8.1 horizons and it currently does not have a generator.

Ok. Here is one for you. Found this when looking under the dash to figure out the electronics on the boat. This looks homemade except for the PC boards. Perhaps something stock that the housing broke on. WHAT THE HECK IS THIS THING ?

I'm looking for a budget option to add sonar to my Garmin 7212 ? I need a IN HULL mount transducer as I don't want to drill the hull. I'm just looking for a good depth and large structure readings. Don't need to find fish just bottom profile for diving. Depths from 0 to 300 feet ??? Any...

Ahh that's not the answer I was hoping for but that's the answer. Thank you very much.

The boat is setup with a NMEA 2k network but its my understanding the I can not just hook the transducer to the network and have the chart plotter read it, I need a sonar module like the GSD24 ???

Looking for some advice on hooking up an Airmar transducer to my Garmin GPS. I have an Airmar – IDST-N2000 triducer mounted in the boat. I have to following Garmin Units GPSmap 7212 GPSmap 547xs GPSmap 541s I would like to hook the Airmar triducer up to the 7212 but it’s my understanding...

Looking the purchase a set of props for 97 330 EC with Merc 8.1 horizons. Anyone have some laying around ?? Also what is the proper prop size ?? Any help greatly appreciated.

Looking the purchase a set of props for 97 330 EC with Merc 8.1 horizons. Anyone have some laying around ?? Also what is the proper prop size ?? Any help greatly appreciated.

I'm looking to put a 16 handle on the transom above the light for use as a grab handle and to mount a flag staff. Does anyone know where the access to this area from behind is ? I looked under the rear seats but there is no access there.

That's great advice. Did you get the gasket from FP ? If might be able to get away with the gaskets but the glass looks in sad shape also. I'd like to replace both. The frame and other hardware look good.

Does anyone know where I can get a replacement bathroom oval window. The glass is cracked and it leaks. The screws to tighten the glass against the seal are screwed all the way in and it's still loose. Also is the starboard side window the same ? Thank you in advance Mike

This is very god advise. I did check the strainer and it looked good and clean but did not flush anything out. I will absolutely do all the easy stuff before the pump rebuild. - Thank you very much

We are getting a weak water flow from our AC. Has anyone rebuilt one of these or just replace? New pump is $350 and the wet end kit is $110. Don't want to waste the $$$ if the wet end rebuild won't work. Any advise greatly appreciated. Mike.

Deposit went out yesterday. I will keep posted. I'm having my mechanic do it. Speaking to Dave it should be very simple but I'm new to boat mechanics. I have done automotive and mech engineering. Once I get some salt on me, I'll start tackling some stuff myself.

We just picked up our "new to us" 97 330 EC. This is our first "big boat" and I'm on a steep learning curve. I have a few items that I need to identify. They both look like thru Hull transducers one has the wires cut ? Any help greatly appreciated. Thank you Mike.