Search results

I am really not sure on the Bahamas ones because I went there in 2008 then again in 2011 so it could be either years. Sorry. Hope this helps.

I am selling the following Navionics Charts- Navionics Gold+ US Southeast-Bahamas CF/906G V13.18 128MB Navionics Platnium US Southeast - Bahamas CF/906P V03.19 2GB Navionics Platnium US Mid Atlantic & Canyons CF/905P V03.18 2GB Navionics Gold+ US Northeast + Canyons CF/904P+ V03.21 16GB...

I am selling the following Navionics Charts- Navionics Gold+ US Southeast-Bahamas CF/906G V13.18 128MB Navionics Platnium US Southeast - Bahamas CF/906P V03.19 2GB Navionics Platnium US Mid Atlantic & Canyons CF/905P V03.18 2GB Navionics Gold+ US Northeast +...

I tried it again, hopefully it worked.

Hello, It is currently not letting me upload the photos right now, so I would be glad to email them to you if you want. Thank you.

I was thinking around 450$. I will post pictures Wednesday when I get back to where the carpet is being stored. The pattern is called Wheaton.

Hello all! I am trying to sell my foam back original equipment salon carpet for my Sea Ray 44 Sedan Bridge 2005-2008 era. Just recently sold the boat and had extra carpet that was never used. The dimensions - 12x11.25 Hasn't been cut yet. BRAND NEW never been used, still rolled up and hasn't...

Hello all! I am trying to sell my foam back original equipment salon carpet for my Sea Ray 44 Sedan Bridge 2005-2008 era. Just recently sold the boat and had extra carpet that was never used. Any ideas where to sell it?

Thanks.... Been years since I've gone inside. Usually can go outside from Wrightsville Beach right on down to Miami but with the Atlantic churned up/Hurricanes, I'm just going to mosy down the ICW. I hear Myrtle Beach is now loaded with dock, so I'm planning a two day trip to get there....

If the ocean is kicked up, we're going to go inside next Friday (Sept 24th) from Wrightsville Beach, NC to Charleston, SC. Our 44 Sedan has 42" draft. Any input on areas that may give me problems. Shoaling, bridges (I know the Sunset Beach Swing Bridge is only opening during high tide)...

I've had my boat for 4 years now. Bought it new. Each time I go to pull up the carpet in the salon to get into the engine compartment, more and more of the carpet backing stays glued to the fiberglass flooring and yesterday 50% of the 1/2" yellow foam backing is now torn off, and remains...

The bottom was just painted 4 weeks ago and engines were re-aligned with new strut bearings installed. I'm goin to check those today with the mask on, but if the bearings were loose, I'd think that I'd probably hear bad noise. After the boat went into the water, it never ran faster....32 MPH...

Agreed, if that were the case. Props are clean as a whistle though, checked below with a mask on.

44 Sedan Bridge 2006. Ever since we have had the boat, occassionaly the Smartcraft Dispay and instrument gauge backlights won't power down even with all of the electrical switches of at the helm, in the salon power panel. I have to go down to the bilge and flip off the "unswitched engine...

44 Sedan Bridge 2006. Ever since we have had the boat, occassionaly the Smartcraft Dispay and instrument gauge backlights won't power down even with all of the electrical switches of at the helm, in the salon power panel. I have to go down to the bilge and flip off the "unswitched engine...

44 Sedan Bridge 2006; QSC 500's Cummings with turbos. After the was boat sitting in the slip for two weeks, I went out and could not get either engine over 1800 RPM. I had the sync on. WOT is nromally 2650 RPM. I have 400 hours on the engines but they normaly purr. The Racors look clean. Any...

Any suggestions?

I need to replace my batteries after 3 years. The originals from Sea Ray were Marine Master (Deka) deep cycle DC31DT's. (4) are used to crank the two engines and run the 12v equipment/lights on board, and (2) are used in series (24V) to crank the bow thruster (which uses alot of juice on those...

The copper 6" screws that go thru the transom holding the large zinc needed to be replaced (the nuts couldn't be removed). The boat yard removed the screws and replaced them with stainless steel screws. From my understanding of electrical circuits, isn't copper the way to go on these screws in...