Search results

  1. A

    My '89 230 Weekender in the water!

    Nice Boat I want to get my 85 230WE out but we just got 4 in of snow. George
  2. A

    Lets see a photo of your pet

    Sundancer now that is a great pic. My 14 year old boat buddy after a day at the lake.
  3. A

    How to measure "hours"

    I have seen inboard ski boats like master crafts with over 4000 hrs on them and still running strong. I have an Infinity inboard with 2500 hrs on it and it runs as good as the day it was built. I think ski boats are used harder that cursers so I think 3000hrs on a well maintained engine should...
  4. A

    fresh water drain

    No wonder I couldn’t fine it. Thanks Guys:huh:
  5. A

    78 sundancer 800 omc outdrive impellor

    You have to pull the out drive. I did it this winter in the boat I bought to make sure I didn’t have any trouble with it. Get a manual and it is not that hard.
  6. A

    fresh water drain

    Does any one know where the fresh water drain (to drain the storage tank) is on a 1985 230 Weekender. Thanks George
  7. A

    Fuel use

    What kind of GPH burn rate are you guys with GM 5.7 OMC getting and at what RPM? Thanks George
  8. A

    Bringing a Classic new Life.

    Nice Boat I have a 85 Weekender 230
  9. A

    12V accessory plug

    I have a 1985 230 weekender, it has 2 prong round 12V accessory plugs to run dc accessories. Does any one know where I can buy the plug that plugs into the boat? Thanks George
  10. A

    Newbe SR 1989 230 weekender

    Welcome, I have learned a lot here. I have a 85 weekender that I bought this winter. I resealed the lower end put a new water pump in it. Took it to the water a mounth ago and every thing worked great. Good Luck George
  11. A

    Alpha 1 drive shaft

    I got the info I needed Thanks Westie. George
  12. A

    Alpha 1 drive shaft

    It is a 1988 alpha one MR, I have done it before on a outboard, I think they set it up with a backlash setting from what I have seen on line. I have a friend that is going to lend me the tools if he can find them, if not I can make what I need. He can’t find his manual. Thanks George
  13. A

    Alpha 1 drive shaft

    I can make the tools, I have a dial indicator I just need the spec. This is an old boat and I am just getting it ready to sell, so I don’t want to buy a manual for it. It is not the one in the pic. Thanks George
  14. A

    Alpha 1 drive shaft

    Does any one have the end play or pre load of the bearing under the water pump for the drive shaft in a alpha 1 lower unit. Thanks
  15. A

    fuel mileage ???

    For you guys that have owned a 230 weekender with a 5.7, what kind of fuel mileage should I expect at a cruse rpm of around 3000 RPM? Thanks George
  16. A

    Shake down cruse

    :smt021 No, you guys don't understand, the 5200 ft is elevation. We have 15% less HP then at sea level. No air here. I got three props with the boat including a shift prop. I will play with those when the water warms up. That 34 MPH was with it trims down, engine turning 4000 RPM, I didn't...
  17. A

    Splashed Yesterday!

    I just put my boat in the water Tues. I live in the Denver area. This is my first cruiser, the boat ran great. I think I am going to like it. George
  18. A

    Shake down cruse

    I put my 1985 230 weekender in the water for the first time since I bought it Tuesday. I have been doing preventive maintenance on it. I resealed the OMC out drive and installed a water pump as well as a transom seal. The boat performed flawless and all went well. The 5.7 260 HP didn’t miss a...
  19. A

    OMC With Power Steering Questions

    Jitts here is one I have more if you want
  20. A

    Used Boat loans

    I just sold a 1993 19ft Ski Ray and had one fellow give me $100.00 to hold the boat for a week while he got financing. I was selling it for $6500.00. He called me back telling me he couldn’t get a loan on anything older than a 2000. He said he was even going to put $3000.00 down and they would...
Back
Top