Search results

Looking for a replacement Voltage Regulator for my Kohler Generator 5E. Anyone have a good used one or any info on a replacement. Power Boost IIIE Voltage Regulator. Would even take a complete controller from a 5e if anyone has a parts generator.

Port tank ran out of fuel last trip long trip coming across lake, was feeding both engines 496 Mags from starboard tank read just under 1/2. was running fine. idling at dock warming up engines and starboard engine stalls like it is out of gas. pulled cool fuel filters and put in new filters...

I need to change out the antifreeze in my Mercruiser MAG 496s (staying with the original Dex-cool antifreeze). New to me boat and want to freshen it up. Is there an easy way to use the extraction pump and pull it out thru one of the lower hoses (which one will get me to the lowest portion of the...

Planning to head over to Toronto From US home port (Wilson). Wondering what the new procedure is with the CBP ROAM app. Looking for any tips what not to bring or issues people may have. Also looking for transient dock we used to stay on Toronto island and take the ferry, 40' vessel. Thanks.

Looking and info on this canvas attachment? It is like a channel I need to attach my new to ne cockpit cover (which has a zipper) anyone have any info?

Are all (like in the picture couplers) with the extended snout with the zerk fitting Steel or are any aluminum? Also anyone have a good picture of the splines looking into it from drive side. I believe there is like a 1" recess until the splines start. I am thinking I need to clean up some...

Trying to reinstall bravo 3 Drive into transom. Alignment is good. I checked it with the bar. Something is holding it from going into the splines can get it into about half inche from studs rotate shaft but it won't engage and slide the rest of the way in. Going back in the morning taking a...

Question should I use anti seize or grease on propnuts and bellhousing studs? Bravo 3

So next issue. Broken 1/4 20 bolt holding water intake housing. Tried today. Heating it with a heat gun and PB blaster was able to grab it with a vice grip but it wouldn't turn. Try the heating and PB blaster if you more times. Anyone have any suggestions? Hesitant to get the map torch in there...

New to me 2005 Rinker Fiesta Vee 360 was stock from facoty 496 Mags Bravo 3 with 2.0 Ratio drives. So here is my issue just checked my drive ratio while servicing my drives port drive 2 turn to one on output (2:1) while the starboard is 2.2 turns to 1 (2.2:1) It has a metal tag that states 2:1...

Replace o-rings on HOSE FITTING for cool fuel gen 3 I am pulling my older style hose fittings on my gen 3 cool fuel module they are slightly dripping. Anyone have the size or part number for these on the white plastic plugs. I would like to have them on hand before I pull them, Thanks

I'm looking remove my engines for a rebuild and gone thru near Buffalo NY area. What was your procedure to remove them? Hoist, excavator boom truck ??? I have 39' 12'6" beam boat. Rinker 360 have to figure best way to remove engines 496s bravo 3s. The engine cover will remove and have pretty...

Bravo 3 prop cleaning? Is it ok to sand blast these or use a ultrasonic cleaner with elma tec clean s1?

Looking to find out manufacturing info on this bravo 3. this is on the tag. I checked mercruisers parts but believe I need for letters?

Looking for opinions anyone think this injector was leaking cylinder compress on that cylinder. Pintel cap was missing on removal but oring was found in manifold. Engine was low on power checked plugs wires fuel pressure reg for paint all good. Compression test is next once injectors are back...

So pulled out my fuel rail for clean my injectors and found 1 injector missing pintel cap. Looks like it has been missing for a while. Wondering if anyone has seen this? I will scope cylinder and check but its probably long gone. The oring was in hole and it definitely was missing when it came...

twin 496 mags bravo 3s WOT Port 4500rpm Starboard 4900rpm 35.3MPH Loaded 4 people full tanks and tools Total fuel 183 gal @ $6.60 = $1205.97 Port 99 Gallons Starboard 84 Gallons the port engine also lacks power at cruise port needs more throttle. New plugs and wires new filters fresh non...

New to me boat. My starboard trim gage wasn't working so pull switch and cleaned contacts. I think it is the gage. But looked at port trim limit and it is the three wire boat is smart craft ready but no smart craft yet. Checking trim limit positions and drive raises they them using trim on...

Trying to add Vessel View to my Simrad Go 9 XSE 2005 Rinker 360 Mercruiser 496 Mag Bravo 3s Manual shift no smartcraft display no Smartcraft Architecture yet. So after researching this, I am looking for two cables to a J Box add a Vessel View 8M0115080 then can I connect to the simrad with...