I have a Cruisair heating/air conditioning unit. It's tripping the circuit breaker and the copper pipe I am pointing to in the picture is getting almost too hot to touch. Any ideas on what could be the problem?
2017 400 Sundancer. Bought brand new in 2018. Never had a problem with the electric swim platform until a couple of months ago, when the fuse (10 amp) started blowing. So far put in a new circuit board ($950) which seemed to help for a few times of using the lift. But then started blowing fuses...
I'm getting a low oil pressure signal on my Cat 3116 starboard engine and it's shutting down my engine. I know it's not the sensor because I swapped the sensor with my port engine and I still got it on the starboard. Also, I know I don't have low oil pressure because I clear the alarm and...
Has anyone who owns an older 400 Sundancer had problems with the carpet in the aft cabin getting wet/stained? I've had this problem for a while, and can not figure our where the moisture is coming from. I was just wondering if anyone else had experienced this and be able to trace where it's...
Back to my favorite forum for help with another problem with my 1997 400 Sundancer. I turn on the breaker for my rear head and I can hear the vacuum pump running for a few seconds and then it shuts off, everything working fine. I turn on the breaker for my forward head, and the vacuum pump never...
1997 400 Sundancer with 3116 Cats. Was driving the boat yesterday when I started loosing RPMs and speed. My passengers were yelling I had smoke coming out the back. I look and there is white and black smoke. Shut both engines down, open the engine hatch and white smoke is billowing out, looks...
I had my bimini ripped off by Hurricane Ian and along with it I had snaps ripped out of my stainless steel windshield frame. I'd appreciate any advice on how to get the broken snaps out and the new snaps in. Thanks
My 1997 400 Sundancer just went thru Hurricane Ian. The rear bimini stainless steel support frame was ripped right out of the fiberglass radar arch. I have the support frame and it is not damaged. My question is what is the best way to repair the screw holes in the radar arch that the frame...
I am experiencing random starting problems with my port 1997 Cat 3116 300hp. The other day I ran it for about 45 minutes, turned it off for about 2 hours, and then it wouldn't turn over. Starboard engine started fine. Emergency start switch did nothing. I could hear the solenoid click for the...
Has anyone had any experience with removing the over-the-refrigerator TV & VHS player? I would like to replace it with a small flat screen TV, but not sure where to start.
Thanks,
drprunner 1997 400 Sundancer
I would like to replace my cabin sliding curtains (the ones that are like 12" or so wide). Does anyone know where I could find them and the hooks that slide into the track. Also, I'm thinking of buying new cockpit carpeting from Matworks. Has anyone else replaced their cockpit carpeting and if...
My 1997 400 Sundancer has a broken starboard trim tab. The hydraulic ram is also broke. Is this a doit-yourself fix or should I hire someone to do it? What's entailed with replacing the trim tab and ram?
Thanks
I have a 1997 400 Sundancer and I need to replace a broken trim tab. Does anybody know what manufacturer and model of trim tab I need to buy? I need to replace everything attached to the outside of the boat, including the hydraulic arm. Thanks.
I recently put my 1997 400 Sundancer into summer storage in FL. I always take out the drain plug as the summer rains get into my bilge thru the air intakes. This year I was unable to get it out and when I use a pipe wrench on it, the plate (held into the transom by 3 screws) that the drain plug...
Both of my windshield wipers need replacing on my 1997 400 Sundancer. The arm is 27" and the blade is 25". If I had to I could make do with just new blades, but I'd prefer to replace the arm too. Anyone know where I can get these parts? Thanks
I have a slow (1 drop every 15-20 seconds) leak in my Cat 3116 raw water pump. It's leaking from the bottom oblong hole in the pump. The pump is 3 years old and the impeller is 4 months old. The pump seems to work fine otherwise, no cooling issues. If it wasn't for the surface rust on the engine...
I have a 1997 400 Sundancer. The shower sump backed up and I couldn't get it to run, so I replaced. The new pump won't run either, so I tried the aft shower pump and that won't run either. I have 3 pumps in the compartment, 2 shower sump pumps and 1 bilge pump, and none of them will run. I...
I have a 1997 400 diesel Sundancer. I recently replaced the dash panels, which requires removing all the wiring to the toggle switches and then reattaching the wiring to the switches in the new dash panel. Well I got every switch rewired correctly, except the starboard ignition switch. There...
I need to replace the props on my 1997 400 Sundancer with Cat 3116's 300hp. I have the original props and am looking to replace them with the same prop. Problem is I don't know the specs on my props and am having a hard time finding the info on the internet. Does anyone know where I could get...