Search results

I contacted sea ray and they just came back with, “put the hull support in line with the stringers that are on each side of the keel.” No custom trailer builders in the vicinity so I’m looking at DIY options. The “clamp on post” that will go on the crossmembers looks like an option. What are...

Right above my main beams, there is the inlet to the generator cooling on starboard and on port is the fitting to the sewage discharge. But I can see a clear path on both sides of the keel to do some runners. the starboard bunk bracket on the back is bent out The center point between the sling...

The main bunks on our trailer go from the back of the boat up past the axles by about 4 feet or so. I saw in your photo some bow supports down by the keel that I need to figure out how to do. How long is your boat?

Here is what the trailer currently has for support basically two big beams and then the bow rest and a lower bow roller that the repair shop took off because they said it was doing damage So I’m not finding magic tilt to be helpful at all Any guidance would be much appreciated. Pardon the...

Magictilt will not give me info to “modify” my trailer. They say they will only share that info with their trailer dealers. I’m in Colorado and closest dealers listed are Texas and California and they wouldn’t have a plan for this trailer since they say it is 3’ longer than they say it should be...

So I can just contact them to get the right fit bunks for that trailer to fit my boat?

Thank you for all your help. I’ve only been able to leave a voicemail for the service dept manager but I’ll keep you posted on the progress (hopefully)

So this is the best pic I have at the moment. Front arrow is a roller low on front of keel. Second arrow is a support with a plastic guard on it. The third mark is a 4” x 10” bunk that runs to the back. It is positioned under a chine (if I’m using the terms right) and when the boat is on the...

Ok. Now I’m worried why the dealer went straight for the jugular and pushing a $18K trailer. Concerns me about the work we have already authorized And then new bunks could be added if it needs more support, right? Thank you for your guidance

These pics are prior to making the tires all load G. 8 lug wheels. Unfortunately I can’t find a good clear pic of boat on the bunks or trailer by itself

I can’t find a pic of trailer by itself and it’s all still at the dealer. The previous owner had a mix of load G and E tires. I replaced all tires with load G.

The trailer in question is a magic tilt aluminum triple axle under a 02 sea ray 340 sundancer. Just purchased this boat last year and took the boat to a nearby sea ray dealership for some repairs to the keel and some other encounters. I get the boat all checked in with service desk and head home...

Ok. Thank you. I looked up those Napa numbers that someone else had posted and it wasn’t matching up to that facet part number so I wanted to see what you found. Again, thank you for your help

Swapped the tach and the one that worked On stbd worked on the port. Port one didn’t work on stbd and twisting the setting knob didn’t get anything working. So now to find a new tach and hour meter. Any suggestions? Thank you Replaced water temp, exhaust temp, and oil pressure switches and...

QUOTE="PlayDate, post: 1170451, member: 764"]Larry, Welcome to CSR! The part that I am concerned about is your generator is behaving like a safety got tripped. Holding down the pre-heat bypasses the safety's. If it runs with the preheat switch depressed.....generally the fuel system is...

So a new fuel pump took care of yours? What did you source for a fuel pump? Thank you

Was your fuel pump success with the facet part number from Napa? I tried ordering from westerbeke but they are 3 weeks out Thanks again for your help Larry

My westerbeke 4.5BCGB will run just fine for about 20 minutes and then shutdown. It will restart but for only 5 seconds after letting off the preheat button. It continues to do this. I replaced water temp switch, exhaust temp switch, and the 2 oil pressure switches and did an oil change with...

I’ll be trying the swap this weekend. Good suggestion. Thank you. the genny is a weird one. Tried to order parts so I can just change parts but westerbeke is holding the whole order till an item out of stock is back in stock and no one answers the phone or returned my phone call yet. Just got...