I cannot use this transducer was going to put it on ebay but figured someone here may need one. I believe they retail for 350 -400?
I'll sell this for $200.oo or b/o
thx Rob
let me know if anyone needs more details. thx
Garmin Gt56uhd-Tm Transom Mount Transducer
Rating:
100% of100
6 Reviews...
Hold the Jokes unless there really funny then go for it. o_O:rolleyes:
Honestly my Coastal inflatable is really sticky to the touch Anyone experience this? Korean made pvc. Only few years old. Tried soap, inflatable boat cleaner. Don’t want to use acetone but may have to try something...
Put boat in the water and even on land intermittently ignition circuit breaker is popping at the dash. 1992 carbureted 350s haven’t dug in yet found loose ignition wire at key but tightened it not super loose. thought that would solve the problem but it didn’t going to start searching for...
Want to get some ideas on how much you use the generator on this boat I have the chance to purchase one for a good price with low hours 8.1 engines not big on AC at sea. I do spend a lot of time on the hook would you buy this boat without generator possibly use Honda? I will keep boat for 10...
I put a new Ongaro horn in my boat and all it does now is click but I noticed looking underneath the panel there is a capacitor that doesn’t seem to be connected to anything on one side one of 2 wires. I played around with it and got a couple of good blasts but it’s hard to get it I was...
Having a hell of a summer so far.....
1992 5.7 running rough loosing power. Changed cap and rotor, no change. Pull plugs all look fine so did I compression check. #6 has no compression 0. All other are 125-150. 600 hours salt water eng that is stored in brackish river.
Rockers are moving...
1992 5.7 carb mercruiser. I was ready to go out last week fired up engine was letting it warm up and it died figured it just stalled started up again ran for another minute stalled again no backfire etc. after a couple of more field attempts would not start. Went down to days later with spark...
3 year old mercruiser manifolds and risers, 30 dancer raw water cooled. I run in salt stored in brackish. Winterized properly by draining water and filling pink anti.
Ran at idle all spring finally got to go out last Saturday and got on plane for about 30 seconds Engines starts bucking and...
1992 300 Sundance one engine won’t start after 4 days of sitting unless I prime the carb. Rochester carbs. Had them rebuilt last season changed mechanical fuel pump no change.
Is there a check valve in the line on this engine? One tank feeds both engines.
I also heard Rochester cards have...
Late in the year my port engine was running warm only at over 3000 rpm. I called mechanic and pulled boat at our YC. He separated drive and 2 blades were missing off impeller. one was inside housing and I had to get the boat back in the water because I could not tie up the club trailer and...
I have twin engine 30' da with alpha gen 2 dirves
I have a loss of power to my stbd engine that comes and goes
it will loose torque and spin out. the problem started last year at the end of the year. new prop plastic hub. I thought it maybe prop so I put on spare prop rubber hub this spring...
I have been having an issue with my stbd engine propulsion.
Engine runs great
I changed props this season because I thought the issue was prop related but it does not appear to be the case.
I go out for a ride and all is well. go thru the locks, hit throttle and all is fine. I hit another no...
Jabsco electric head works sometimes then gets jammed other times. If I manually move it with pliers while pushing button I can get it to flush.
Is there a rebuild for this or just replace?
Do I need to order the motor only or Motor/pump?
anyone know of the cheapest place to get this motor?
Guys I have an issue with the "roller" on the shift at the engine cable side not seating correctly. This is causing the the boat to not start. tough to explain but the roller should be sitting in the center of the "V" and it is sitting out of alignment. The roller position controls spark to...
Hi all, getting close to that time up north here. I was wondering if anyone has had success restoring the aluminum windshield frame on the older 90's Rays? mine is chalky looking and hoping to get it looking better this season.
Also, dash on my 92' is very faded and wanted to see if that could...
I am looking for replacement vinyl for my 1992 sundancer. it is the bright white with dk and med blue and with red piping. I see loads of vinyl on FP site but can't figure out by the pic's which one is the match for my boat. only doing the flip up pad on stern. anyone have experience on how...
About a month ago on my way to Aquapalooza I throttled up 92, 350 i/o 300 da and heard rapping.
went back to dock took Valve cover off and pressed in stud was lifting up and rocker came loose. fixed temporarily for the day.
Took head off and found bent exhaust valve on #5 cylinder. Replaced...
Checked previous posts and could locate on this subject. My 350 raw water manifolds are running hot but risers are cool to touch? I have not taken them apart yet (soon). boat is still out of water but they ran hot last fall as well.
Impellor is 1 year old, Manifolds and risers are about 9...