Search results

Hi, my 1995 Sundancer 330 DA engine hatch is lifting very slowly to the point where it only moves a little then I have to wait a minute to move it more. All of my batteries are fully charge, just in case someone thinks that could be the issue, that was my first thought. So I am looking at a...

So I solved the issue with the motor not getting up to full rpm, took it out, ran for about 30 minutes at 3200 rpm cruising fine. Stopped the boat for about 1.5 hours offshore to fish, then when tried to start, it started right away, then stalled, then would not start again. Checked carb and no...

I am looking for help in running the battery cables from the engine room to a new inverter in the cabin, then tying that into the AC/DC panel in the boat, since there is no generator, I want to use the switch for gen for the inverter so not to accidentally switch on inverter while on shore...

So I took the Sundancer 330DA on a test run, both motors ran great up to 3000 rpm, except past 3000 rpm, port motor would easily go, up to 4000 rpm, starboard engine would not go past 3000 rpm even at full throttle. Also the starboard motor has a few small back fires when she starts cold..not...

So both of my voltage gauges on helm show fine when idle or off, but when I start revving the motors, the voltage gauges start bouncing low... This is happening to both of the motor gauges.. 1995 Sundancer 330DA with Carb Mercruiser 7.4l Thanks!

Figured I would start a post for this instead of tagging it into my replacement for Raymarine SL post..

Does anyone know what newer chartplotters will fit into the opening for a SL520 Raymarine unit? I am guessing that the unit was original on my 330DA 1995... Just looking to upgrade to a newer system. Thanks!

Hi, I only need the board. Thanks!

Hi, I am looking for a replacement systems monitor panel for a 1995 Sundancer 330 DA Mine is randomly going off various alarms and lights. Anyone know a source for these? Thanks!

Hi, I am trying to figure out if the wiring is bad or how I can activate the second (higher) bilge pump (Rule 1500) on my boat? I only see one bilge pump switch at the helm and have tested the pump itself, but when connected, it never turns on, only the primary lower pump turns on. Have cut back...

Hi, I am getting a warning horn and light at any rpm over 1000 on both of my v drives and have no idea what is causing it? boat is new to me, so do not have any experience with her. Boat is a 1995 Sundancer 330 with 7.4l Mercruiser engines. V Drives are: Hurth hsw 630 v1 Any ideas? Thanks! P.S...

Does anyone know what the best size sheet set would be for a 1995 330? King, Queen, or is there a special size offered somewhere? I guess same goes for what size bedding for dining table and aft bunk?

Hi, do you think it is a good idea to carry spare props on a 1995 Sundancer 330 with v-drives? and if so, what size props do you recommend? the boat currently has 3 blade props, not sure the size? also if anyone knows the shaft size, would be great Thanks!

Hi, can anyone tell me how many and what size zincs I will need? Boat will be in saltwater full time. Thanks! P.s. the boat has v drives

Hello, does anyone know if a 1995 Sundancer 330 with 7.4 v drives can be off loaded from a flat bed with a fork lift or does it have to be a travel lift with slings? And any considerations I need to tell the driver when it is loaded? thanks!

Hello, does anyone know what the min generator wattage would work for a stock 330 sundancer (1995) with a 12k btu marine air system? The old generator was missing and not sure what they came with, looking at a small 3kw onan as a replacement possibility. Thanks!

Hello, does anyone know the bridge clearance for the above boat with arch? Thanks!

Hi everyone, I am getting ready to pull the trigger on a 1995 Sundancer 330 with a 7.4l carb and v-drives and wanted to know from anyone who has had or has that year model what their real world min draft is? I live in the Florida Keys and have a 3 foot min draft requirement. Note from the...