Search results

The new trim gauge worked. I guess the test of shorting the sender post to the ground post and seeing if the needle moves doesn't necessarily mean that your gauge is good after all.

LOL!! I think the word "terminology" is being kind. I figured I would probably lose some people trying to describe what I was doing. I know the timing indicators you described. Mine were not perfectly aligned, they were off by about the width of the mark. When I aligned them perfectly it did...

I did some testing this evening and believe I may have two problems. The trim sender wire runs through the transom and has two barrel connectors in the engine compartment that plug into the connectors labeled Chassis Ground and Analog Trim. I unplugged those and connected the positive terminal...

So if I combine what Thornton69, scoflaw, and ttmott said, I should set my multimeter to ohms (it's auto-range so I can't select 200 watt range), disconnect the sender wire from the back of the gauge, touch one probe to the sender wire and one to the gauge ground. At full down trim I should see...

Yes, I should have said multimeter. Thanks for the details. I'll try it this evening. And yes, I think I know about the timing mark on the sender. When you pull the puck off the outdrive, around the hole where the asterisk-shaped hub sticks out, there is a small mark at the edge of the hole...

Good to know. I'll check, but the senders are new. Replaced them last year and only used in fresh water since.

So to test that, do I stick the voltmeter probes to the sender wire and ground wire behind the gauge and check voltage while the trim is raised up and down?

Used Quicksilver Part 805320A03.

I've been trying to diagnose an issue with my trim gauge. The gauge hasn't worked since I bought the boat about 18 months ago. It reads down all the time. At first the trim up didn't work, only the trailer switch worked to raise it. Last year I replaced the senders when I did a bellows job...

I've been trying to diagnose a problem with my trim gauge not reading correctly. I was back at the trim pump and noticed that the nut holding the fuse where the battery cable connects to the pump was loose. So I disconnected the battery cable from the fuse connection and tightened the nut...

Yeah, so far from my reading, that seems the most likely culprit.

LOL!! I know the feeling. I’m basically an IT guy who has just enough knowledge and tools to tackle something with cars or boats, and usually end up throwing tools around the garage and making up new cuss words.

Thanks for the replies everyone. It's not drive lube. Mine has the reservoir under the hatch to monitor it. Drive lube is good. I also once tried unplugging that sensor to see if that stopped the beeping and it did not. Impeller is good, I replaced it last winter when I pulled the lower unit...

Just FYI for everyone, this problem continued even after replacing the IAC and muffler. I ended up having the fuel pump replaced. It wasn't keeping pressure up once it got warmed up. The mechanic said the old pump was down low on the port side of the engine. They replaced it with a newer style...

2002 Sundeck 220 Mercruiser 5.0 MPI. Boat runs fine but will usually start getting the 2 beeps per minute alarm. Sometimes it will stop for a while, but it eventually comes back. It may happen at idle on the flush kit, at idle in the boat dock, or at speed. Sometimes I just turn the key on...

Sorry I'm so late with feedback about this. A lot of things going on lately so I haven't had the boat in the water in a few weeks. I installed a new IAC and cleaned the muffler. Took it out today and ran for a couple of hours, starting and stopping. No more alarm and it cranked every time...

I was out on the water yesterday and had an issue for the first time. I cranked up and idled out of the basin and went for a ride for a few minutes. Boat ran fine. I shut down and cranked back up and started getting the 2 beeps/minute. Oil pressure was 40-50, temp never over 170, drive lube...

Sorry for the late response. After watching numerous videos and tutorials and pictures so I better understood what I was looking at.....you guys nailed it. Shift bellows - the narrow end was completely torn loose and was letting water flow in unobstructed. I have the outdrive off now getting...

Thanks for the tip!!

Hi All, New Sea Ray owner here. I live in south GA, but was hoping to go down to Pensacola on the weekend of July 14 and put the boat in to view the Blue Angels during the airshow that weekend. I have been to Pensacola, mainly the beach, but don't know my way around very well. I wondered if...