Search results

  1. D

    Shifter

    I need to swap out the 3000 classic side mount shifter on my 96 Sundancer 250. Does anyone know if it will come out through the panel on the wall in the head or out the engine bay area? Wont fit through the speaker hole unfortunately. Was going to leave cables hooked to it until its out. It...
  2. D

    Shifter

    I need to swap out the 3000 classic side mount shifter on my 96 Sundancer 250. Does anyone know if it will come out through the panel on the wall in the head or out the engine bay area? Wont fit through the speaker hole unfortunately. Was going to leave cables hooked to it until its out. It...
  3. D

    Shifter

    Hi Guys, I have a 96 250 Sundancer. I need to swap out the shifter assembly. 3000 series. It will not fit through the hole that its mounted or the speaker hole. Does anyone know if it will come out through the access panel in the bathroom or out the bilge area?
  4. D

    shifter

    hello, does anyone know the oem part # for the 1996 era quicksilver 3000 classic side mount shifter?
  5. D

    Shifter

    Hi, I have a 96 Sundancer 250 with a Quicksilver 3000 classic shifter. It needs to be replaced but it's no longer available as far as I can see. What unit will replace it? This one has trim up down, and trailer button. I dont want to spend 5-6 hundred. Just something comparable. I plan on...
  6. D

    power trim issue

    So over the winter I installed new trim and limit switches. I am in need of a wiring schematic for the sensors. The boat harness ends do not have any connectors so I am not sure what color the wires are. I was able to figure out the limit wires, but I am unable to figure out where the other...
  7. D

    Garmin or tablet

    I'm not new to boating but, I am a newbie as far as chart plotting goes. I boat in Western Ma. lakes and the Hudson River. I'm looking to head out to other areas this coming summer and I would like to be able to see where I am, where I am going, and also be able to map out a safe route and not...
  8. D

    trim

    Good morning! So the wife and I made our last run of the year down the Hudson River this weekend from Albany to the Kingston City Marina. What A great time! Now for my problem. The trim gauge is not working anymore. (the trim DOES still work though) What happened is that I trimmed the boat out...
  9. D

    pcv system

    So I have a question about my PCV system in my 96 Sundancer. I know that on a car the hoses from the PCV valves run to a port on the carb or intake manifold. Why does a boat engine run the hoses to the Spark Arrestor and not to a vacuum port? The reason I am asking is because I have very slight...
  10. D

    Temp Reading

    So I just repowered my 96 Sundancer with a new 7.4. Boat runs great but I was wondering what the coolant temp should be when running in the water? The gauge is reading just under 100 deg all the time. When I shut the engine off and let it sit for 10 min and turn the key on it will read 175 deg...
  11. D

    sea water pump

    Hey all, I am installing my new 7.4 into my 96 Sea Ray Sundancer 250 that I removed last fall. I am having a problem determining witch location to put the hoses on the sea water pump. All the pictures I look at show them in either location? Hoping somebody can help me out!
  12. D

    454 EFI

    Another boat question. Does anyone know if a 96 Sundancer 250 came with a Multi Port injected 454? I know they did come with TBI. I am just wondering if there is height difference between the two. The fuel systems are totally different between the two. Also I am wondering about the shift and...
  13. D

    RE POWER

    I have a 96 Sea Ray Sundancer 250 DA with a gen 6 454 carb. Bravo one drive. The engine is no good. I have access to a 2001 Mercruiser 5.7 MPI engine. This engine is plug and play. Can anyone tell me what is involved in this change over? What will be the biggest issue? I was told it is a direct...
  14. D

    454 to 5.7

    New to the boating world. I am however a Ford Certified Tech. I have a 96 Sundancer 250. I am wondering what is involved with swapping out my Gen 6 454 with a complete drop in 5.7 MPI unit? I know that I may have to change the steering rack because the fittings on the hoses are not the same. How...
Back
Top