Search results

Sold boat, have these brand new (never installed) parts for sale: Free local pick-up.....shipping is at your cost. Mercruiser 50-808011A1 Starter - $175 https://staugustine.craigslist.org/bpo/d/palm-coast-mercruiser-a1-starter/7608009380.html Mercruiser Alternator - $75 (DB Electric)...

Can anyone give a recommendation on an Insurance Broker in the area? I currently have Geico/BoatUS but I think there has to be other companies who can do better. I am hoping a broker could help me "shop around". My 380DA is in the water year round behind my house in Palm Coast. Thx!

Good luck to all as Ian approaches....Extra lines, fenders, full tanks, charge all your portable radios etc etc The ONLY nice thing about having a boat in the water during/after a Hurricane is that you can crank the genset and live aboard if your house power is out for some time. Stay...

From my 2000 380DA with 7.4's Was fully functional when I removed it last month but as you can see the DDU is damaged at the reset button and the display is very hazed and hard to read. The interface functions as designed with "All Systems Normal" displayed until alarm beeps with engine...

I got tired of the cheap white plastic windlass deck switches and upgraded to the Maxwell covered stainless steel ones. Very heavy duty and makes the foredeck look better. Simple remove and replace installation.

In the process of updating the original SR Systems Monitor to a simple LED light with alarm. I see my Hurth V-Drives have a transmission overheat sensor on them but I am not sure if it triggers an alarm thru the system monitor? I think it is "Normally Open" and I tried closing the circuit to...

Totally stumped....was time to replace manifolds, risers and exhaust elbows as preventative maintenance on a totally running fine port motor. I also installed new seawater impeller and flushed and visually inspected the heat exchanger. I saw some signs of water reversion inside the riser...

Was tired of looking at the rust stained white PVC jacketed lower lifelines so I decided to upgrade. Took down old lifelines and measured pin to pin overall length. Realizing the aft turnbuckles were redundant I took them out of my measurement for the new ones. I made new ones out of .316 1x19...

So....bit the bullet and purchased a new Whaly 270 rotomolded dinghy (from the Netherlands). I have seen them as work boats and daily use tenders and I was impressed as to the stability, ruggedness and compact size...

I have an Intellipower PD2140 in great shape that I removed from my SR380DA. I dont know how old it is as it was in the boat when I purchased it on the latter part of 2018. It was (and is) working as it should going thru it charging cycles to maintain my batteries. I removed it as I am...

Hi: Searched the forum and couldn't find any info.... My question is on the 2000 SR380DA, can you remove the Teak Grate in the shower to clean underneath, remove hair etc etc I am thinking "no" as I pulled on it and it is in there solid. I assume its another one of those "what were they...

2008 SeaRay 380DA came in to the marina on one engine. Captain said it "threw the belt" and all the engine alarms went off. It ended up being the bearing in the belt idle tension/pulley exploded and sent shrapnel everywhere. New one to match up locally could not be found, so they went home on...

Hi: Hoping to get some feedback from fellow owners who have gone thru this: I am removing the original carpet from the cabin and will be replacing with vinyl plank flooring, aluminum trim around the floor hatches and solid Ash wood companionway steps. WTF did they use to glue the carpet down...

Went out on the boat yesterday. Aligned Stbd side shaft a few weeks ago.....(important part of story to remember)..... Did my usual fluid etc check and everything looked ok before I fired up. Stbd side motor would run for 1-2 seconds and alarm would go off and then shut down. Fluids ok but...

As part of my (possible) removal of Hurth V-Drive to replace the rattling Drive Plate while in the water, I decided to build a Heavy Duty prop puller to keep on the boat. I just completed my DIY Hookah system so I jumped in the water to check dimensions for a prop puller. There is ample room...

Hi: Getting ready to head for the exumas and adding spare parts to my boat inventory. I am looking for pair of spare (or just one even) spare props for SR380DA.....1-1/2" SHAFT, 21 X 22, 4-BLADE. They dont have to be in spectacular shape, just a spare set to get me home or to the nearest prop...

Quick question....on a 2000 SR380DA with 454 MAG MPI's and V-Drive......to push/pull the propeller shaft all the way back to the dripless seal ....do I have to remove the rudder or will the propeller shaft somehow clear/pass the rudder? Propeller will be removed. I need to remove V-drive to...

Hi: After diagnosis of all other possibilities, on my Stbd 454 MAG MPI, Hurth V-Drive Damper plate needs to be replaced. I understand what needs to be done as far as sliding the prop shaft back, sliding the V-drive forward (making sure to support the engine block) and removing the bell housing...

Hey 1999 SeaRay 380DA with twin Mercruiser 454 MAG MPI's.....went to change the spark plug wires and I noticed that the Stbd and Port engines have the same cylinder wires going to different points on their respective distributor. I know the firing order is 1-8-4-3-6-5-7-2 for both motors? but...

Hi: 2000 SR380DA with Mercruiser 454MAG MPI's, V-Drives......engines running strong, new oil and fuel filter change, clean bottom, always run non-ethanol. Since I have owned the boat (2 years now) the STBD engine has had a "rattle when idling in neutral or in gear at idle speed. Rattle...