Search results

I have read many posts that say that the 330 is the a great overall boat, I just sold my sea ray (older one) and am looking at an 04 300 its nicely appointed with painted hull, twin 5.7 bIII drives generator, camper back canvas, seems thats is one of the better years smart gauges fuel filter...

i need to get the starter out of my starboard motor and i just cant get access. i have remnoved the exhaust manifold but still to tight, is there a particular way method pposition to jack up the motor. if i put a 2 ton piston style jack under the starboard side with a piece of plywood under...

I have a 2 lowrance transducers, 1 is mounted mid ship, and 1 transom mount, is theree a reason to have 2 that i might not be aware of, and can a transducer from one manufacture (lowrance) be used with a different manufacture product (Simrad)

Yes it would seem so, I called the deaker and they said remove the exhaust manifold so I hope that’s going to be the fix cause I can’t get my fat hands down there

does the engine have to be removed/tilted/lifted to replaced the starter in a 89 searay aj with twin 4.3's, or is there a trick to it

my 270 is fwc my question (which i feel stupid asking), but when you take the rad cap off the heat exchanger should it not be filled with rad fluid, and is it just standard antifreeze nothing special.

Thanks guys were can you look up this info on the drives, I am stumped, and I work with computers so I am computer savy, I didn’t have the boat surveyed, I didn’t pay that much for it, considering what they can go for. I got into it only seeing one engine run which is fine as I can figure that...

Thanks for your response, I haven’t confirmed with an expert from the pictures I have seen and used to compare they look like b1’s. I can find any serial numbers on the drives themselves just the ones on the transom plate and a few other things Indicate they are b1 drives. Apparently the seller...

Bought my boat last friday, the seller didn't have props for the boat. So I assumed they were stock alpha 1 drives. After doing some research i have found they are Bravo 1 drives. I have to double check the engine serial numbers once I am back where my boat is store but they are definitely mpi...

Thank you both

I tried looking it up on some charts, is there a site I can confirm this myself or what number indicates bravo 1

looking at purchasing 4 x g5 fenders (2 per side) . I was wondering how many fended everyone else used, where they placed them and how they mounted there fender racks. I am guessing 1 fender stern and 1 mid ship. I think if I put it at the bow it wouldn’t support the boat against the deck...

Anyone know where you can identify accurately what leg i have, hers the serials in case anybody knows off the top of there heads. Port Leg: 0W113491 Starboard Leg: 0W775490

newly purchase boat, bought 2 new batteries as there were none with the boat. there are 2 battery trays, 1 perko battery switch, for a single battery. were these from the factory installed with a single starting battery and a single for house. anybody that has a similar twin engine boat i would...

thank you, but no that's no it, i will take a picture and post, i believe it has 4/5 bolts going up, ground, power in, tilt up, tilt down,

Thanks Phasma for you list, greatly appreciate

little ducky I downloaded the owner manual and i agree very informative, but could you possible direct me to engine, drive, etc manuals.

Totally understand I didn’t take it in a bad way, sometimes a gentle reminder is needed for all of us. I wrote the post rushing out the door boat part shopping as I just picked Jonny boat on Friday and just checking to see what mess I got myself into. Bought a partial project one engine ran the...

My apologies you are right a little courteous goes along way, so humbly I ask for some help, and offer a please and thank you in advance.

looking for an annual maintainence/walk through checklist someone else has for a twin engine boat. hopefully in excel, something you step through methodically to make sure all systems are working properly,