Search results

  1. mmills023

    Volume Sea Ray Dealers

    Outside my local area - I was wondering who are the biggest or largest volume Sea Ray dealers in the US? Looking for a dealer that actually has some inventory (i know all are low) Mike
  2. mmills023

    Chicago boaters?

    Morning! - I think a few of us are over at Burnham Harbor - I would be interested in a meet/float up at some point. Also feel free to DM me at anytime with any boating questions you may have. If i dont know, I can point you in the right direction! :) BTW...can we call ourselves Chicago...
  3. mmills023

    40 sedan bridge forum

    When I was looking for 400DB's before I found the one I purchased I inquired about the cost of adding a bow thruster, as many I was looking at didnt have them. I found the quotes to range from 8K - 15K. I ended up factoring that into my purchase price when considering ones without. It does...
  4. mmills023

    40 sedan bridge forum

    I think it may say bennett...i may have found the replacement...BTW..40.00...hmm
  5. mmills023

    40 sedan bridge forum

    actually...one of the actuators inside the switch broke...well at least I assume as the port side went "limp". Is that a taylor part? Mike
  6. mmills023

    40 sedan bridge forum

    Does anyone have a picture of...or part number for the trim tab switch on a 2002+ 400DB - one side of my switch broke this weekend and I didnt take pictures...thinking it would be easy to find...my bad! Thank you in advance.
  7. mmills023

    40 sedan bridge forum

    Problem is I can’t find where the other side plugs in..I looked for about an hour...had my wife get up under there as well...no luck. I was hoping someone had a pic or could show me where to look.
  8. mmills023

    40 sedan bridge forum

    So yesterday I attempted to repair the head system on my port head. First...the access is SO small for a big guy like me...moving on...what i found is that on the pump on top of the vacuflush there are 2 wires with spade connectors. there is a red or orange (couldnt tell) one that is not...
  9. mmills023

    40 sedan bridge forum

    Wanted to see if anyone had any thoughts. My guest head system does not seem to be working. Here are symptoms. I turn on "Head Systems", the Master Head starts to create vacuum, the lights on both heads turn on. The guest head does not appear to be pulling vacuum, its almost like the...
  10. mmills023

    40 sedan bridge forum

    Through the hatches in the salon - usually a long cherry picker in the cockpit stretched through the sliding door (which they may have to take out). Gas will be easier than diesel.
  11. mmills023

    Show off your dock

    Ours...nothing special but great access to Chicago.
  12. mmills023

    40 sedan bridge forum

    I meant to say....55' :)
  13. mmills023

    40 sedan bridge forum

    taylormade part number 8319400 I just bought 60' (think you need about 5')
  14. mmills023

    Show us what you do, stuff you make

    I just sell stuff!!
  15. mmills023

    40 sedan bridge forum

    Quick question - While I am resealing the windows, I wanted to reseal some of the other areas on the boat, Arch connection, etc. has anyone done this, if so what type of caulk did you use for that? just a high quality outdoor caulk?
  16. mmills023

    40 sedan bridge forum

    thats a big improvement - did you apply by hand? buffer?
  17. mmills023

    40 sedan bridge forum

    I am getting ready to embark on this project....had a question. Did you just put the flooring over the existing floor in the galley? Any height issues? I am sure you could fill a book, but any "I wish I knew this before I started" type things?
  18. mmills023

    40 sedan bridge forum

    Mid April would be nice...here is Chicago we get started in July ;) LOL . The marinas open May 1st, water finally warms up by Labor Day!
  19. mmills023

    40 sedan bridge forum

    I want to seal all my windows not sure what sealant/caulk to use. Has anyone done this? What did you use? Color? How many tubes?
  20. mmills023

    40 sedan bridge forum

    I just replaced the bulbs, it was a pretty easy process. A tip...if you dont already have a good way to get the light housings down to replace bulbs, try the metal end of a tape measure...it slides right in there and a with a little tug comes right out. Here are the bulbs i bought. (all from...
Back
Top