When I launched the boat, I had a flag stuck between the outdrives and the starboard engine was stuck up. Shut everything down and restarted and all started working well. Since this, i have had intermittent issues when I shift the starboard into reverse, it does not shift. Last night, i can...
I launched my boat and am having the following issue. I can only start the Starboard engine when holding down the emergency start. The port engine is fine. Furthermore, the VV403 is not powering up either. The boat runs fine, I took it out last night for 20 minutes at about 1000 RPM and came...
My mechanic pulled this out as it was leaking and replaced it with a new pump. I’m selling is as it. It does require to be rebuilt.
FYI - impeller replaced year before.
Pump Sea water part #: 46-862914T11 or 8M0139996
Pulley part #: 862351T or 8M0150724
a new pump is more than $1100 with a...
I changed my seawater pump earlier in the week, ran the engine at the dock, and all was good. The same things today warmed up the engines and started moving using the joystick. i typically use the joystick for the first couple of hundred yards. Back up from slip, turn around, and then start...
Finally launched the for the season (latest as I was looking for parts). I noticed the noise coming from the pump. After some diagnostics, I learned that the pump pushes the water out to a vertical outlet, but some of the water will remain in the hose. The water drains back to the box and a...
Mine cracked over the winter and when I took the blue plug it all cracked. I looked up the part and it's 863802T2 (closed-loop). The problem I have is that I can't find the part anywhere. It's back-ordered from Mercury until July (called all local suppliers and no one has it)! I have ordered...
I wanted to share what I have done and more than happy to answer any questions. I have upgraded to a new electronics and panel on my cruiser. I call this project phase 1. Phase 2 will include a Fusion unit and Fanthom Radar.
I'm looking for a solution for the white lettering on the black...
I have SR310 DA 2008, and looking for the best location to install the NMEA 2000 network. The easiest power location is under the helm, but space too tight. Looking for recommendations on where you installed yours? pictures would be great if possible.
I'm selling the following. All working and in great condition. Please feel free to ask any questions. The reason for the sale is a new panel with new electronics.
Mercury / Sea Ray 4-1 Gauge (N02 069 035) - 5" Oil Pressure, Water Temp, Volts, Drive Trim - $275
Mercury / Sea Ray - Tachometer (02...
SOLD
Selling Garmin ECHOMAP™ Plus 74cv - 2 years old. Was installed new when purchased on a used boat at MarineMax. reason for selling is upgrading my electronics. I pulled out of the boat this morning after updating the software to the latest version.
I'm NOT selling the transducer. I will be...
Hi all, starting my spring project to upgrade electronics and looking for some help. I purchased a VV403 and got it connected and setup over the weekend. the boat is winterized so I did not start the engines just put the key into the on position so that I can get the VesselView to work. However...
I'm looking for the service manual in PDF, where can I download it from? I was able to download the operations manual from the mercury marine EMEA site.
The part number was pulled from the mercury marine parts catalog. > Sterndrive > Engines - Gas > 6.2L (377 CU IN) V8 GM > 377 MAG MPI BRAVO...
I've been having issues with STBD engine stalling at idle after a full day of boating. Low voltage error. I used a voltmeter and got he following results:
Key is in OFF position, batteries on
Voltage at alternator is 13.3V
Voltage form the 50 amp fuse is the same
Voltage going to stater is the...
I changed my batteries after my second outing this season. they were 3 year old and can still hold a charge. Reason i changed was because the starboard engine would shut down. After changing the batteries, everything was good for a couple of weeks until yesterday and today. Last night, after...
hi everyone, the genset ran for less than a minute and then gave fault of CO 6. In the manual the fault is inoperable CO sensor and the recommendation is replace the CO sensor. Does anyone have a part number? is this is simple change?
I did search the forum but nothing on this particular...
I Launched the boat on Monday after winter storage. Both engines started but had an message for low voltage on the starboard side. Before I stored the boat for the winter, i got the same message for the port engine. I though this was related to leaving the boat as it was on land and batteries...