Search results

  1. CNYBoater

    1994 200 Overnighter - 194 V135hp Outboard

    1994 Sea Ray 200 Signature Overnighter Outboard 135HP on 2004 Trailer 20' Cuddy Cabin V hull boat with a Mercury BlackMax 135 HP oil injected outboard of same year. I purchased this boat for my family of four in 2017 for use on Oneida Lake. Cruise between 25-30mph, WOT on flat water 40-42mph...
  2. CNYBoater

    Pinched a wire while mounting switch box

    I had removed my switch box to replace a suspect white/black jumper wire between the inner and outer boxes. When I replaced the boxes, I pinched the violet wire from trigger to the inner switchbox between the two boxes. While I have small enough heat shrink connectors to splice it if needed, it...
  3. CNYBoater

    Is my canvas repairable?

    Shrink has been off and cockpit canvas has been on for a week. Was at the storage yard Saturday and arrived to find my canvas is damaged. I’ve a message into the yard to see if they will check cameras for me. No response yet from the canvas shop that made it local. any thoughts to this damage?
  4. CNYBoater

    1994 200OVOB - My god, what happened?

    Finally had some time to head to boat to look into my running issues, or best said, lack of running issues. Not warming up, idling rough, hard to keep it running. After last time out, pulled the new plugs and no soot and wet fuel mix on cylinder 1 and 3. This test was after I replaced plugs...
  5. CNYBoater

    1994 200OVOB - My god, what happened?

    Finally had some time to head to boat to look into my running issues, or best said, lack of running issues. Not warming up, idling rough, hard to keep it running. After last time out, pulled the new plugs and no soot and wet fuel mix on cylinder 1 and 3. This test was after I replaced plugs...
  6. CNYBoater

    Recommendation need on Outboard testing

    I want to do a compression test, but based on symptoms I think it’s more likely the trigger or switch boxes. In regard to this, all the compression testers I can find have very short leads and I will be single handing these test following the service manual instructions. Any recommendations...
  7. CNYBoater

    Faria Euro 7k outboard tachometer

    My faria tach is two months past the 3yr warranty. I’m experiencing a signal that reads slightly below 1000 at idle 650+\-50 is spec. Increase throttle and tach won’t past 1200, though the outboard is throttling up. anyone know the ohm specs on a tach signal from voltage regular to gauge? In...
  8. CNYBoater

    Weekend vacation - whale watching

    With the admiral’s birthday being divisible by 10, she wanted to do a whale watching tour. Scratch it off the list thing as she’s caged dived with sharks and gone dolphin watching already (but without me, while traveling for work). For the weekend, we headed towards Boston, 5.5 hr drive from...
  9. CNYBoater

    WTS used 48-88440A4 14x19P SS Prop

    Used quicksilver 14 by 19P 15 spline right hand stainless prop part number 48-88440A 4 19P asking $100 or best offer. Did some looking around marketplace and Craigslist, so priced this prop down based on that research. Also, If an established Club member wants to try it for a size/pitch...
  10. CNYBoater

    Beautiful Day

    Great day on Oneida Lake. Glad that the forecast was wrong.
  11. CNYBoater

    Anyone a financial broker, or pleased as punch with one?

    The world has gone crazy, environment in New York State is business toxic, and employer is shutting down. I'll be phased out in a few months, my mostly vested 401(k) will need a trustee to trustee transfer as I can't stay in a plan that will be closed. I work with BoA as my personal bank, and...
  12. CNYBoater

    Does this look like a helm seal fail?

    I purchased some fluid dye for my hydraulic steering, went out tonight to take a look since I couldn't see anything with the UV light during the day. I can not tell if what I am seeing is the spill over from when I unattached the filler tube running behind the dash, or if what I am seeing is...
  13. CNYBoater

    Need a SeaStar Hydraulic Steering Mail In Repair Recommendation

    1994 Sea Ray 200 Overnighter w/ Mercury 135hp Outboard. End of last season during the driveway system test before going out on a day trip, found the steering almost gone, inspection showed fluid had drained into splashwell then out of boat, only a little residue left in splashwell. Anyways...
  14. CNYBoater

    1994 200OVOB Fuel Sending Unit Replacement

    Looking to replace my fuel sending unit. I've had it out of the boat once to check the float when I first bought the boat. Turned out the problem then was the ground wire was corroded. So I replaced it with new tinned 8awg with soldered ends direct to battery. The sending unit that is in there...
  15. CNYBoater

    Bennet Dealer - Effectiveness and Mounting Self Leveling Tabs on 200OVOB Question

    Just curious looking at the mount patterns on the 10"x10" self leveling tabs. I have a 1994 Sea Ray 200 Overnighter 135HP Outboard. The transom on my hull is angled forward on either side of the outboard. Will tabs be effective since they would not be perpendicular on the transom. Seems like it...
  16. CNYBoater

    Anchor rope setup question

    Does anyone mark off 5 or 10' markings on their anchor rope? I was thinking it'd be a good idea to know how much I'm letting out for scope since its wound up on a spool in a compartment when not in use. I was thinking colored coded electric tape, but then got thinking that might not hold up...
  17. CNYBoater

    WTB: Scrap Marine Ply or HDPE 16.25"x25" min .25" thick

    Looking to buy an end piece or scrap Marine Plywood or HDPE. I Stepped on my in floor cooler lid and the screws pulled out of the 24 year old Marine Plywood. The 6-pack sized cooler box screws into a half inch thick piece of bilgekote painted marine ply which has two more layers of 1/2" marine...
  18. CNYBoater

    1994 Mercury Black Max 135 on 200OVOB - No Charge

    I recently installed new gauges and noticed that my poor voltage readings carried into the new gauge, as well as all gauges dipping doing trim usage. I rewired the gauges with new marine tinned 14 gauge wire as the old non-tinned 16 gauge wires are just old, being a 1994 boat. changing the wires...
  19. CNYBoater

    Fuel Tank & Grounding

    Last year, I had no reading on my fuel gauge. I pulled up the deck hatch over the tank and found the grounding wire to be non-tinned and very corroded. I ended up cutting back 6" of cable from either end of the 8AWG ground wire and restored signal. This year, I replaced the ground wire with new...
  20. CNYBoater

    Replacing Ignition Switch & Adding Safety Kill Switch

    I have a 1994 200OVOB HIN # SERV3370L394 and 1994 Mercury 135HP O/B serial # 0G016519 Model 1-135422P The boat came with 1 ignition key, and the ignition kind of twists in the mounting hole when you turn it over. I'd like to replace the whole ignition assembly for a new one, mostly so I have a...
Back
Top