Search results

Hi all 2004 280DA with smartcraft. MY depth shpwing dashes, does anyone know 1. what model OEM tranduscers are installed so i can look for a replacement 2. are there aftermarket ones available 3. is it best to leave it and install a new one somewhere to connect to my raymarine A98 thanks

Hi all I'm looking to get my Mats done over in foam and the company has a 2006 template only. ANyone know of any differences between the cockpit layouts- pretty sure they were the same from 2002 to 2007 Thanks

Hi all Have a sundancer 280 with 5e generator. Its running but the exhaust port where the water comes out has a frothy gas smell. Any suggestions on what the issue is? Gen does not get used much-i know they must be ran but always forget to run it even when not needed just to keep it running...

Hi All Sundancer 280 with the dual mercury throttle. The port side top handle (black part) is loose and spins. Is there a set screw somewhere to tighten it? Or do I need a new handle. Ive seen handles but mine has the dual trim buttons and ones I see don't have. Or is it universal and I need to...

hi all Is there any other location or way to locate engine serial number. The metal tags on mine are unreadable and I need it for a repair 2004 sundancer 4.3

hi all Any advice on this one 2004 sundancer 280 starboard will not start. Cranks fine, fuel pump kicks in but when I try to start I get a non stop beeping. Drive oil fill is fine. Thanks

hi all went to turn water system on and steady water js coming out the port side rear thru hull connected to the water heater or maybe water pump. Mechanic says water heater is bad. He bypassed the water heater mainly because I've never used hot water and the labor intensive task of...

hi all Need some direction. 04 sundancer 4.3 First ride out smelling gas out back of boat and looks like fuel in the water. Mechanic thought bad Injectors. Took them out and replaced 2 and serviced the others. Still getting smell. Engines run fine no issues whatsoever. Any ideas? Thanks

Always wanted bow cushions for my 280 . finally made a template and got some custom ones done. Added snaps and keder track to keep them still.

Hi all O4 280da out on water today got port engine alarm that said pressure ( assuming water pressure sensor). When I rev engine in neutral psi not increasing. When in gear after 2k rpm says overspeed engine power reduced. Got towed in and started back up and now no alarm and psi is...

Looking to take our first trip to fire island from freeport on our 280DA and looking for a captain to show us the way. I hear there are some shallow areas and dont want to rely on the charts for our first trip. Any recommendations? I have a few but they havent been available. Thanks

Hi all Boat was hit and cracked rub rail at bow/anchor. looking for recommendations of anyone on south shore long island that can repair I imagine they just cut a new piece in? Thanks

Hi all. 04 sundancer. Does anyone know what size chain and rope works with the gyosy. Need to replace. Is it 1/4 in g4 with 1/2 in rope

Hi all 04 sundancer 280. Smartcraft digital fuel showing gallons working but gauge stuck in half. Any ideas ive read how to test sender but dont know if these 2 work together and maybe its the gauge Thanks

Selling a m625L thermal night vision camera. In good condition. One lens has salt deposits on it but doesnt affect image. Its a dual payload with the low light camera as well. Comes with new jcu and poe ne er installed. Just plugged it in at house to take images. Originally almost $20k...

hi all. looking for feedback from owners of flir thermal cameras. In process of installing one on my 280da and center of radar arch is taken by radar. so have to go to port side of arch which is not straight just where it starts to curve downward. not a terrible amount but wondering if that...

hi all Does anyone know if the raynet cables provide poe? Possibly adding a 232thermal camera to my ray a98 mfd and didnt know if it needed seperate power or if the unit provides the power to ray net connected devices Thanks

hi all. Does anyone have pics or directions for installing the camper support poles. Instructions say outside of edge of non skid on one side and behind non skid on the other. Kinda have an idea but one already installed will help. Thanks

Hi All Port engine starts, revs fine but when out on water and I give it gas it stalls and bogs down sometimes causing engine to stall. suggestions for others says prop issue?? any ideas.. thanks

H all. Was Out on water everything was fine. Port engine shut off. Wouldn't turn back over. cranks strong- fuel pump seems to be working, new dist Cap and plugs this season and pulled plugs to make sure no water got in. They were Good. Any ideas frm the experienced guys out there is...