Search results

pulled the soft hatch this week and the yard forgot to unscrew the tracks that hold the aft seat and they bent them. anyone ever replaced these aluminum tracks that line the floor in the cockpit area of the 460? it looks like this but not sure if anyone had an exact match or supplier they’ve...

That's helpful. I think you are right, that we have two separate problems here. Still unsure about what to check / test with the engine unswitched breaker that is on that panel. When it trips, should we manually check all systems to see what else is tripping? We have two others that are...

Its a 2001 Sea Ray with 10BTDA westerbeke. We swapped the wiring to another breaker and it did the same thing unfortunately so not the breaker.

We have a 460 DA Sundancer with a Westerbeke generator. We started with low power out of the generator and when we switched from shore to generator, the "Engine Unswitched" breaker would trip in our main companionway breaker panel. We changed the voltage regulator and are now getting full...

Which one?

Has anyone ever had issues with the throttle body on older style (2001-2003) DAs? My throttle (stainless with gold balls) is incredibly stiff and is that way even with the cables disconnected so isolating it to the throttle box itself. Is there a way to grease the internals of the unit and...

Yes I am referring to the actual frame - contemplating just sealing it shut at this point.

Need to replace throttle cables on our 2001 460 with Cummins 6CTA- seeing numerous cable lengths in the parts manual. has anyone replaced these before with the same engine setup and if so, do you recall the length? I don't want to pull them only to find that our local store doesnt keep the...

Hi Kevin, if we were to drill them, how would be re-attach the new ones? We may go the route of the SNADS if they seem to hold up ? How can I purchase? I may try that route first and see how it goes.

Has anyone ever replaced the inside panel on their 460 windshield? The frame around our windshield vent is thoroughly corroded and I would like to just replace the whole thing if possible. Anyone else have this issue?

Have several eisenglass snaps in our windshield on our 460 that appear to have snapped off with the rivet inside. Is there a tool to remove/replace the rivets that are installed inside the windshield? For clarification, they used to be the male side of the snap that is now just a flat spot...

Cheryl, where did you source the portlights from? We need to do this job in its entirety as well.

Thanks for the insight. How did you get longer studs? Use an extension? It seems the studs are fixed, so would need to add an adapter? When you say notched the frame, do you mean the bulkheads under the deck? Any pictures you may have ? That would be super helpful.

Has anyone changed windlasses from the progress 1 to the project 1000? My progress 1 crapped out and we decided to replace new as the unit was seized. While the project 1000 is a drop in unit, the space it takes up under the deck is much wider and doesn’t fit, as the motor hits the aft bulkhead...

thanks, got those. unfortunately my top track is the broken one...

Looking to replace my sliding door tracks on the 460- has anyone done this and know the measurements off-hand? I need to send them to FP Marine when i order them and figured someone has already done this and they should be the same?

We have a 460 with flag blue hull paint, we’ve started noticing that between or biannual waxes we have what looks like salt caked in the paint. We rinse the hullsides after every use but this seems like it’s stuck in there. I don’t want to have to on/off the hull every couple months or move up...

Our dometic AC pump, 331554, crapped out this weekend and need to find a replacement. Seems like hard to find online, did they change the part number? Is there a cross reference to another March pump?

Went down there again this morning and found that my rear suspended track (not on the floor but inside the molding), is cracked and its allowing the door to move off the floor track. Would need to remove the door in its entirety to get to this and replace.

Ive searched extensively here on the site about this salon door and cant find anything. Even spoke with Sea Ray which didnt help much. Our outer gliding door which pulls the inner door with it seems loose in the track, which causes it to lift from the back when you pull it across and it lifts...