I would like to disable the over temp. alarm on my boat:
19' 1988 SeaRay Seville #SERA6274L788. 135 Outboard V6 #0B278686.....
1) I need the location of this alarm module.
2) I need the wiring color code for this module.
Now running pre-mix fuel and all oiling equipment & parts have been...
Can anyone provide a picture of where the wiper is mounted on an 88 Seville. I would like to install a wiper but am not sure where to drill the hole. Thanks
Also, anyone know where old SeaRay part numbers can be located (ie:Windshield wiper)
Slyclops
I got a set for my 88 from a guy in Seattle who had several spares made out of stainless steel. I don't know if he has any left now, but it's worth a shot, his contact info:
jon@petrowskiassoc.com
His name is Jon, and his phone is:
(360)737-1854
Good Luck
Slyclops
OK, I've found a paint supply that sells gel coat by the pint ($15) + $5 for the hardner. Is there anything else I need to add to the gel coat (gray coloring, etc.)?
Is there any special preperations needed other the clean and dry (like roughing up the edges, etc. etc.) before I apply the gel...
Holy Moly! I called my nearest S/R dealer today re: the gel coat paint, he said it was $95 a quart, plus a special $25 hazardous UPS shipping fee from back east. Needless to say I'm not buying that stuff! The salesman did give me the name of a local paint distributor (SVENSENDS in Oakland Ca)...
Can you brush on gel coat or is there special procedure?
The place I'm repairing (a storage area) has a 1X1 stapled all around (all 4 sides) the interior surface. One of the 1X1's was crushed thereby allowing water to get in and cause some dry rot. I have removed as all the dry rot I can see...
Do you have any stock of the "GelCoat" type paint used in the bilges and storage areas of older (88) S/R boats? If not, can you suggest a source?
Thank You,
Slyclops
Thanks Fwebster,
While looking up "Bilgecoat" in a West Marine catalog, I found a product called "Watertite Epoxy Filler", it sort of sounds like a pretty stuff as it is a two part epoxy, but I'm going to try and find a S/R dealer that might have a quart of the original in stock, wish me luck...
I am looking for the brand (or something simular) epoxy type paint that was used in the bilges and storage areas of 88 Sea Ray Seville Bow Riders. If you've got a clue, please email:
slyclops@gmail.com
Thanks.........
I just purchased an 88 and it does not have one, but, I intend to install one for when I'm out screwing around and having a good time and there is just the slightist possibility that I could lose control (fall overboard, lose my footing, fall backwards from my seat, bla, bla, bla). It cost way...
Hey EricTheViking,
So, did you get your tank out?
I just purchased an 88 Sea Ray 18' Seville BROB and was thinking about putting in a larger fuel tank. Was there any extra room in your storage area for a larger tank? Keep me updated. Thanks,
Slyclops
Thank you for your input. I know how to mount it, I need to know "WHERE" to mount it. Are there any secret spots on and 88 Seville where the Mfg. has provided a location for this purpose? ie: like next to the fuel tank under the floorboards, in the ski storage area in the floor, etc.. Thanks...
I recently purchased a used 1988 Sea Ray 18' "Seville" Bow Rider/Outboard. I would like to get in contact with others who own this boat so we can exchange ideas and offer tips to each other.
Slyclops
No help offered from me, just a question. I have a 4" patch of dry-rot where some dropped something heavy and broke the factory seal/paint. Anyone know of any kind of chemical or "Whatever" that I can shoot into the hole before I re-seal the area. Does dry-rot grow if no more water is present...
I have an 1988 Sea Ray 18' Seville Bow Rider/Outboard. I would like to mount an "In-Hull" transducer, but don't know where to put it. I know some boat builders provide a spot for this equipment, does anyone know if Sea Ray did? Or have you done it and where did you mount yours?
Thanks,
Slyclops