Hi All,
I've found a cheap way to polish fuel (I think). I got a diesel fuel transfer pump (gear, not impeller) from Amzn (about $90), then I disconnected the fuel hose from the Racors, connected it to the pump (needed a fitting to do so), then disconnected the fuel hose that goes to the tank...
Hi All,
I searched, but couldn't find this info. I have the Uline Ice maker on the bridge. It is working, but the compressor is making a horrible noise every now & then. It is 12 years old, so I'm expecting it to die soon. Any recommendations for a replacement? (I'm not changing to a...
I have two 6CTA’s in my 450EB (2400 hrs). I just changed the oil 5 hrs ago (Rotella 15w-40, same oil I’ve been using in these engines for 11 years). Oil pressure is always approx. 50 PSI for both engines (helm gauges). Yesterday, strb engine went down to 20 PSI (verified with mechanical OP...
Hi All,
The fridge/freezer works on 12v, just stopped working on 120 v. I have a part # 169000600 for this power supply (it does not output anything, checked all the connections, fuses, etc.,), but can't find one. Does anyone have a good source for it? And I'm assuming this power supply...
Hi All,
I need some help. I’m trying to finish a prop shaft/coupler alignment on my boat (’99 450EB w/ Cummins 6CTA’s, and they are v-drives).
I’ve determined that the front end (fan belt end) of the strb engine needs to move inboard, probably just 1/8” or so. I have all the engine mount...
Hi All,
Anyone have a good way of cutting the "tails" off zip ties when doing electrical work on the boat? Every time I work on my electrical stuff (or plumbing, etc., where there are zip ties) I look like I've been in a knife fight afterwards. I always get cut. I cut the tails with wire...
Hi All,
Anyone know how to repair this (look at Down & Temp button)? I was hoping just the mylar overlay could be changed/available, but that is not the case. I don't want to buy a whole new control panel as it works fine, it is just the buttons that are wearing out.
Thought/ideas?
Thanks...
Hi All,
I have 2 fresh water Jabsco Par-Max3 pumps @ 3.5 GPM (plumbed in parallel, I run them both at the same time). I have had them 6-7 years. They have been ok. A bit noisy, which I actually like as I know when they are running, but ok. I had a pressure switch go bad on one this past...
Hi All,
I need a new push to start engine switch. It is a Carline off-on-(on) VM4J 670521, but I can't find it online. Anyone have any info?
Thanks as always
Larry
Hi All,
Need your help. I have a 1999 WB 10BTD with 2,400 hours on it. Today, it went wacky. On first start up, output voltage was 180 v (vs 220 normally). I checked/flipped all the breakers, no help. I shut it down, waited about 5 mins, restarted, now it only puts our a few volts (maybe...
Hi All,
I finally bought this tool to help install the impellers in the seawater pumps in my Cummins 6CTA's. I have no affiliation with the company, but I have to say I am very impressed. It used to take 2 hours or more to do my impellers the "old fashion way", mainly because the pump on the...
Hi All,
My 20 year old WD 802 M Splendide washer/dryer died this weekend. Any experiences on choosing a replacement? Stay with Splendide? Other brands? Where to buy? I'm limited to the same size due to cabinetry.
Oh, and especially if you have made this replacement in this boat (99' 450...
Hi All,
The coolant recirculating pump on my Westerbeke 10 BTD needs to be replaced <leaking, bearings bad, pulley wobble>. A new pump is $380! Does anyone have any experience with getting a new pump cheaper? Can it be rebuilt by an owner? Other suggestions?
Thanks all!
Larry
Hi All,
Need your help. Boat is a '99 450 EB with a Weste 10 BTD with the Searay one button start module. Genset has 2000 hrs on it and has been good. Today, when I went to start it, I accidently "double-pushed" the button and now it won't crank or start.
I've checked for voltage, all seems...
Hi All,
I have 3 AC's on board. When the master AC kicks on I get a ground hum in the 12v salon stereo amp. When either of the other 2 AC's kick on, this does not happen. I've check at the grounds and all are good. Any idea on how to fix?
Thanks for the help.
Hi All,
My original fuel tank senders are not very accurate <as we all know>. I would like to have something more accurate. I do not need anything fancy <NEMA 2000, etc.>, I would just like to retrofit the current gauges with better senders. Do you have any recommendations?
Boat is a '99...
Hi All,
I have 2 ships radios and 1 handheld that are DSC. Should you use the same MMSI #'s for all radios on board? If you press the red button on all 3 would they transmit at the same time and cancel each other out? Should there be separate MMSI numbers for each radio?
Thanks
Larry
Hi All,
The boat is a '99 450 EB. The guest shower overflows into the "dry area" where the sink is. It's not the drain, I've cleaned it out, even drilled the holes in the drain plate bigger. It's the angle of the floor that leads the water under sliding glass door into the dry area. I'm...
Hi All,
I need some help. Boat is a ’99 45’ Express Bridge with Cummins 6CTA’s with ZF IRM280VLD V-drive transmissions. All shafts, props, cutless bearings were pulled, checked, replaced when we got the boat 3 years ago. Strb prop has always been a big harder to turn than port. Alignment...