I’ve tried searching with not much luck. Does anyone know a part number or source for replacement shower and floor drain metal trim grates? I’ve had what looks like the exact same ones on a 2004 34 Sundancer, 2007 40 Sundancer, and now my 2001 56 Sedan. I believe it’s a standard part for the...
Hi guys,
I posted this on Boatdiesel, but thought Id run it past this board as well.
I have a pair of 800hp 3406E in a 2001 560 Sedan Bridge. The boat is new to me as of a couple months ago, and we took our first big trip this week to Key West and back. I noticed as I was pulling into my slip...
New owner of a 2001 560 Sedan Bridge. Most AC units on the boat are new, but the flybridge 24k BTU unit is original and quite loud. It works, but I have to believe its days are numbered based on how loud it is. Just had service checkup on the whole AC system, and the tech said it looked like a...
This winter during lay-up I had all engine mounts replaced on my 2007 40 Sundancer with QSB425s. Cummins Minnesota replaced the mounts, as well as serviced all the boat’s coolers and replaced hoses and clamps.
With the boat now back in the water, Im noticing substantially more vibration than...
2007 Sundancer 40 and I’m looking to replace the thru-hull lugs and all hardware for the transom zinc.
The nuts I took off look to be stainless, but the lug bolts themselves almost look like they are bronze.
Anyone know for sure?
Thanks
Eric
2007 40 Sundancer with QSB 5.9 425 Cummins. Survey at purchase 3 seasons ago mentioned the mounts were getting close to needing replacement. Several are now totally collapsed with the rubber pretty much sitting directly on the stringer and what I consider an excessive amount of engine vibration...
Im installing a pair of Garmin plotters, new autopilot, and GSD24 network sounder on a 2007 40 Sundancer. I purchased a tilted element Airmar B60 thru-hull transducer, and am just looking for advice as to where to install in the hull. Id like it to work as reliably as possible, and hopefully...
Hi all,
Boat is a 2007 Sundancer 40 with Cummins. Wondering if anyone has successfully run wires from your engine room to the cabin main panel. There is what appears to be an extra conduit with its own pull cord on the starboard side of the engine room just above the fuel tank, and I have found...
Already posted this in the other electronics forum, but this seems like the more appropriate place to ask the question.
2007 Sundancer 40 with Cummins and factory dual E120s and no DSM with a Systemview SC5000 screen. I believe the Airmar smart transducer DT800 should supply water temp to the...
2007 Sundancer 40 with Cummins and factory dual E120s and no DSM with a Systemview SC5000 screen. I believe the Airmar smart transducer DT800 should supply water temp to the systemview, but the readout always reads the same temp. Depth works great.
Should I go straight to replacing the...
2007 40 Sundancer with Stainless Windshield. The factory snaps for the front isinglass are deteriorating to the point that they are almost inadequate to keep the glass up. Would like to replace them, but they are riveted into the frame and I'm a bit skittish about drilling them out. Definately...
For sale is never-used snap-in carpet for a 2006-2008 Sea Ray 40 Sundancer. I believe it will also fit a 2003-2005 39 Sundancer (same boat).
Recently purchased the boat and the previous owner had this carpet made brand new for the sale. I will be installing teak decking and wont be needing the...
In the process of buying a 2008 300SLX. Has anyone had any experience removing the radar arch? Even better, has anyone modified it to be collapsable for low clearance?
I have a heated indoor storage space with a 9' door, and intend to store the boat there during the winter. Wont fit with the...