Search results

  1. crizz

    58 Sedan Bridge Official Thread

    Thanks for the info. Sent you a PM.
  2. crizz

    58 Sedan Bridge Official Thread

    Carter, Who did your AC work? I am in Fort Myers Beach and my 56 Sedan still has the original 24k Cruiseair unit on its last leg. What is your initial impression of the CTM unit? Glad to hear about the boats in this thread that survived Ian. Sure has been a year to forget. We are around the...
  3. crizz

    Replacement shower/floor drain trim

    Thanks for the replies guys. It seems that the trim piece should unscrew from the underlying drain. I was hoping there were replacement trim pieces that would screw back into the same drain without having to cut it all out. I’m not interested in doing that at all.
  4. crizz

    Replacement shower/floor drain trim

    I’ve tried searching with not much luck. Does anyone know a part number or source for replacement shower and floor drain metal trim grates? I’ve had what looks like the exact same ones on a 2004 34 Sundancer, 2007 40 Sundancer, and now my 2001 56 Sedan. I believe it’s a standard part for the...
  5. crizz

    New to Sat TV on the boat

    Those of you using Hulu to stream live TV, how do you get around the location check? My experience is they will only allow 4 location changes every rolling 12 months.
  6. crizz

    560 Sedan Bridge Flybridge AC Replacement

    We are in Fort Myers Beach. Boat is at a shared private dock currently, but will be behind our house once our dock is modified to accommodate her. Its currently a 8-10 month wait to have dock work done here. Your 58 looks spectacular! That was my first choice, but unfortunately the current...
  7. crizz

    3406E Smoke at idle

    Also, the oil analysis did not show any excessive soot (or any other issues) on either motor.
  8. crizz

    3406E Smoke at idle

    Thanks for the comprehensive reply. The engines have about 1750 hours. I had a full hull and separate engine survey done prior to purchase with only minor issues noted. I did oil analysis at both the pre-purchase and just prior to a full service that was just completed by a certified CAT repair...
  9. crizz

    3406E Smoke at idle

    Thanks guys. I hadnt thought about the air filter, but will add that to the list. The smoke is certainly not white or blue, or the thick black that Ive seen come from old Detroits in working boats. Id call it grayish.
  10. crizz

    3406E Smoke at idle

    Hi guys, I posted this on Boatdiesel, but thought Id run it past this board as well. I have a pair of 800hp 3406E in a 2001 560 Sedan Bridge. The boat is new to me as of a couple months ago, and we took our first big trip this week to Key West and back. I noticed as I was pulling into my slip...
  11. crizz

    560 Sedan Bridge Flybridge AC Replacement

    Thanks for the replies guys, sorry for the long delay. Finally got some decent pics.
  12. crizz

    560 Sedan Bridge Flybridge AC Replacement

    New owner of a 2001 560 Sedan Bridge. Most AC units on the boat are new, but the flybridge 24k BTU unit is original and quite loud. It works, but I have to believe its days are numbered based on how loud it is. Just had service checkup on the whole AC system, and the tech said it looked like a...
  13. crizz

    Vibration after new motor mounts

    So far, I cant even get Cummins to call me back about it. And finding a boatyard willing and able to do the job in Minnesota is proving to be harder than you'd think...
  14. crizz

    Vibration after new motor mounts

    This winter during lay-up I had all engine mounts replaced on my 2007 40 Sundancer with QSB425s. Cummins Minnesota replaced the mounts, as well as serviced all the boat’s coolers and replaced hoses and clamps. With the boat now back in the water, Im noticing substantially more vibration than...
  15. crizz

    Transom bonding plate lugs

    2007 Sundancer 40 and I’m looking to replace the thru-hull lugs and all hardware for the transom zinc. The nuts I took off look to be stainless, but the lug bolts themselves almost look like they are bronze. Anyone know for sure? Thanks Eric
  16. crizz

    Linear Actuator for Hatch Lift

    I know that I am resurrecting this thread from dead, but i was curious if those actuators from Progressive Automations actually worked? I just got done installing two 400lb lifts thinking that was more than enough oomph for my 40 Sundancer (same boat as your 390) and they will not lift the...
  17. crizz

    Cummins engine mounts - 40DA

    2007 40 Sundancer with QSB 5.9 425 Cummins. Survey at purchase 3 seasons ago mentioned the mounts were getting close to needing replacement. Several are now totally collapsed with the rubber pretty much sitting directly on the stringer and what I consider an excessive amount of engine vibration...
  18. crizz

    Making water under the engine

    Have you considered AC condensate? It would take quite awhile to accumulate 8 gallons, but not out of the question.
  19. crizz

    Airmar B60 Transducer Installation

    Thanks for the replies. Im not "stuck" with it, but its usage will be so light Im just not sure it makes sense to pay double or triple for functionality I probably wont need. Do you have anything specific another unit would provide considering 100% of my boating is in a freshwater lake with max...
  20. crizz

    Airmar B60 Transducer Installation

    Im installing a pair of Garmin plotters, new autopilot, and GSD24 network sounder on a 2007 40 Sundancer. I purchased a tilted element Airmar B60 thru-hull transducer, and am just looking for advice as to where to install in the hull. Id like it to work as reliably as possible, and hopefully...
Back
Top