Search results

I went to clean out the sea strainer for my A/C and the plastic handle broke and the strainer will not turn to remove it. Has anybody had this problem? How did you fix it? TIA.

On my 2007 320 DA the outside fridge door will not open. I pull the latch at the top of the door but it stays latched. I've searched the forums as well as googled with no luck. Any ideas?

I have had an issue with my port engine. My wot is only 4000 rpm, should be 4500-4600. And at this rpm I am getting a distinct raw gas smell. If I lower the rpm the smell goes away. I get no warnings or faults on my sc1000 gauges or VV Mobile. Any ideas?

My masthead light has gone to the graveyard of broken boat parts and I have a new one. Does anyone know the nav/anchor wiring colors for the masthead light? The labels have worn off. I know black goes to ground but which powers the nav and which powers the anchor from the cockpit switches? thx

Does anyone know the size of the two screws that fasten the TPS to the throttle body? My mechanic is coming later today to remove them because their heads are stripped and I want to have new ones available for him to put the new tps on. 2007 Mercruiser 6.2L inboard.

I posted this in the repair and maintenance section, but got no help. Anyone replaced a TPS on a mercruiser 6.2l? It appears the IAC is in the way. Is it possible to take the whole IAC assembly off so you can get to the TPS screws? Thanks for any help.

Anyone replaced a TPS on a mercruiser 6.2l? It appears the IAC is in the way. Is it possible to take the whole IAC assembly off so you can get to the TPS screws? Thanks for any help.

Does anyone know the auto equivalent of the TPS mercuiser p/n 8m0097035?

I accidently did a master reset on my port SC 1000 gauge after replacing a water pressure sensor. I went throught the autodetect mode and now I am getting a lost engine com warning. There is nothing in the owner's manual about this. Gauges all worked fine until I did the master reset on the...

Does anyone know where I can get a replacement actuator for the portside ER hatch lift? The motor is still good but the shaft is bad. Tried to get info from Acculift, the original supplier, but no go.

My ER hatch has has stopped working. The breaker would trip usually when putting it up all the way. I would reset it and it would work again. Then it started to trip when I opened or closed the hatch with the bilge blowers on. I took it to have a transducer replaced and the hatch would only...

I have a 2007 320 DA. My question is about the bilge switch on the port side of the helm. Which bilge pump does it control? I'm having issues with my aft bilge pump. When I press the switch the green light comes on but nothing happens. Thanks in advance for your responses.

Posted this in the 320 thread with no response, thought I would try here. My bilge pumps are not working properly on my 2007 320. Does anyone have a good suggestion on how to reach either of them in the ER? My arms aren't long enough.

I posted this in the 320 DA thread but thought I'd try here. The tab(blue plug) on my starboard side fuel pump drain broke off and the plug is in the drain. Has anyone encountered this and if so how did you get it out? Thanks in advance.

The tab on the fuel pump drain plug(blue plug) on my starboard engine broke off and the plug is leaking. Anyone ever encounter this and if so how did you get the plug out?

Anyone know of a place that repairs the LCD screens on boat gauges? I have an SC1000 that the screen is almost burned out and can barely be read. I've scoured the internet for a replacement gauge but I can't find any.

I just had a survey done on a 2007 320 DA. The survey found a few minor problems but nothing you wouldn't expect on a nearly 10yo boat. After the haulout portion of the survey and the boat was splashed I had a compression check done by the mechanic from MarineMax. The boat sat in the water for...

Newbie here, waiting on a seatrial of a 2004 320 DA with 540 hours. My question is the owner just had an oil change how long would the boat have to run in order to do an oil analysis?